Hitachi HVM Navigator V03-06 User Manual Download Page 56

Page: 56 / 312

2-34

Usage environments

HVM Navigator User's Guide - Migration

Note on expansion of VNIC System No.

•

CB2000

When you execute LPAR migration in Shutdown mode between HVM firmware
59-11/79-11 or earlier and 59-21/79-21 or higher, and the VNIC System No.

set for the HVM firmware 59-21/79-21 or higher is 129 or greater, you cannot

execute LPAR migration in Shutdown mode. Check the combination which you
can execute LPAR migration in Shutdown mode in the following table.

Table 2-59 LPAR migration on HVM on CB 2000 standard server blade

Destination

Source

HVM firmware version

59-11 or earlier

59-21 or higher

HVM firmware version

VNIC System No.

128 or smaller

129 or greater

59-11 or earlier

128 or smaller

Yes

59-21 or higher

128 or smaller

Yes

129 or greater

Yes

Table 2-60 LPAR migration on HVM on CB 2000 high-performance server

blade

Destination

Source

HVM firmware version

79-11 or earlier

79-21 or higher

HVM firmware version

VNIC System No.

128 or smaller

129 or greater

79-11 or earlier

128 or smaller

Yes

79-21 or higher

128 or smaller

Yes

129 or greater

Yes

•

CB500

When you execute LPAR migration in Shutdown mode between HVM firmware
01-30 or earlier and 01-40 or higher, and the VNIC System No. set for the

HVM firmware 01-40 or higher is 129 or greater, you cannot execute LPAR

migration in Shutdown mode. Check the combination which you can execute
LPAR migration in Shutdown mode in the following table.

Table 2-61 LPAR migration on HVM on CB 500 server blade

Destination

Source

HVM firmware version

01-30 or earlier

01-40 or higher

HVM firmware version

VNIC System No.

128 or smaller

129 or greater

01-30 or earlier

128 or smaller

Yes

01-40 or higher

128 or smaller

Yes

129 or greater

Yes

Shutdown

Summary of Contents for HVM Navigator V03-06

























































































































































































































































































































Search results

Summary of Contents for HVM Navigator V03-06

Reviews:

Hitachi HVM Navigator V03-06, User Manual, Page: 56 / 312

Search results

Summary of Contents for HVM Navigator V03-06

Reviews: