manualshive.com logo in svg

Hitachi HVM Navigator V03-06, User Manual, Page: 298 / 312

Share
Download
Hitachi HVM Navigator V03-06 User Manual Download Page 298

 

 

6-36 

Troubleshooting 

HVM Navigator User's Guide - Migration 

op1 

op2 

op3 

Message [interpretation] 

Suggested action 

0x00 1******* 0030 02  0x0000 0000 0004 ffff 

0x01  The MMS could not define an 

LPAR because there is not 
enough memory in the 

destination blade. 

Reserve enough amount of 
free memory in the 
destination HVM and then 

retry migration. 

0x00 1******* 0030 02  0x0000 0000 000A ffff 

0x01  The MMS could not define an 

LPAR because the name of 
the specified LPAR is 

'NO_NAME' 

Rename the migration 
specified LPAR to a unique 
name in the system and 

then retry migration. 

0x00 1******* 0030 02  0x0000 0000 **** ffff 

0x01  The MMS could not define an 

LPAR because the specified 
LPAR has an unexpected 
condition. 
[Unable to define an LPAR at 
the destination to have the 
same configuration as the 

source.] 

Reserve enough amount of 
free resource in the 
destination and then retry 

migration. 

0x00 2******* 0030 02  0x0000 0000 0000 0000  0x01  The MMS could not define a 

USB port on an LPAR because 
the specified USB has an 

unexpected condition. 

Check source and 
destination LPAR 

configurations and retry. 

0x00 3******* 0030 02  0x 4-byte_VnicID 0001 2-

byte_VnicNum 

0x01  There is not enough VNIC 

device#3 (Virtual NIC: 2a) to 
define an LPAR. 
[There is no NIC at the 
destination corresponding to 

the NIC at the source.] 

Inspect the physical 
configuration of NIC (LAN 
adapter) at the destination, 
reconfigure it to meet that 
of the source, and then 

retry migration. 

0x00 3******* 0030 02  0x 4-byte_VnicID 0002 2-

byte_VnicNum 

0x01  The MMS could not define a 

VNIC#3 (Virtual NIC: 2a) on 
an LPAR because the 
specified VNIC has VLAN IDs 
which are not acceptable in 
the destination blade. 
[Unable to define an NIC at 
the destination to have the 
same VLAN configuration 

settings as the source.] 

Inspect the physical 
configuration of NIC (LAN 
adapter) at the destination 
as well as review the NIC 
settings (VLAN mode and 
VLAN ID) at the source, 
reconfigure them to meet 
each other, and then retry 

migration. 

0x00 5******* 0030 02  0x 4-byte_VnicID 0003 2-

byte_VnicNum 

0x01  The MMS could not define a 

VNIC#3 (Virtual NIC: 2a) to 
a promiscuous mode because 
this mode is not acceptable 
in the destination blade. 
[Unable to define a VNIC at 
the destination to have 
promiscuous mode in the 
same configuration as the 

source.] 

Inspect the physical 
configuration of NIC (LAN 
adapter) at the destination 
as well as review the NIC 
setting (promiscuous mode) 
at the source, reconfigure 
them to meet each other, 

and then retry migration. 

0x00 3******* 0030 02  0x 4-byte_VnicID ****  

2-byte_VnicNum 

0x01  The MMS could not define an 

LPAR because the specified 
VNIC#3 (Virtual NIC: 2a) has 
an unexpected condition. 
[Unable to define a VNIC at 
the destination to have the 
same configuration as the 

source.] 

Inspect the physical 
configuration of NIC (LAN 
adapter) at the destination, 
reconfigure it to meet that 
of the source, and then 

retry migration. 

Summary of Contents for HVM Navigator V03-06

























































































































































































































































































































Reviews:

No comments