Hitachi HVM Navigator V03-06 User Manual Download Page 265

Page: 265 / 312

Troubleshooting

6-3

HVM Navigator User's Guide - Migration

Taking action when LPAR activation has been disabled

Event

When the execution of Migration functions has failed, activation (power-on) of
the source LPAR or the destination LPAR may sometimes be disabled. HVM

screen shows “The specified LPAR has corrupted in an LPAR migration, please

try to recover the LPAR.”

Solution

Execute manual recovery of the activation-disabled LPAR in accordance with

“Executing manual recovery when automatic recovery is not done” in this
chapter.

Taking action when Policy migration has failed

Event

When Policy migration has failed, the following window pops up. In such a case,
follow the procedure in “Solution” below.

Figure 6-2 Confirmation window

Summary of Contents for HVM Navigator V03-06

























































































































































































































































































































Search results

Summary of Contents for HVM Navigator V03-06

Reviews:

Hitachi HVM Navigator V03-06, User Manual, Page: 265 / 312

Search results

Summary of Contents for HVM Navigator V03-06

Reviews: