manualshive.com logo in svg

Hitachi HVM Navigator V03-06, User Manual, Page: 294 / 312

Share
Download
Hitachi HVM Navigator V03-06 User Manual Download Page 294

 

 

6-32 

Troubleshooting 

HVM Navigator User's Guide - Migration 

Detailed error information detected by Migration Management 

Client 

Format 

“EMG” op1 : don’t_care : don’t_care : (don’t_care) : ”MMC” : message 

•

 

“EMG”: Fixed characters meaning error message. 

•

 

“MMC”: Fixed characters meaning Migration Management Client. 

•

 

don’t_care: Values at this position are negligible. 

•

 

op1: 1st operand that identifies error detail in hexadecimal code. See 
Description. 

•

 

Message: Error detail in text. See Description. 

Table 6-1 Error message detected by MMC 

op1 

Message [interpretation] 

Suggested action 

0x00 00000000 0001 01 
0x00 00000000 0003 01 
0x00 00000000 0004 01 

Connection refused (MMC-MMS) 
[Migration Console module (MMC) 
cannot connect to Migration 

Management module (MMS).] 

In the “Option” window opened from the “Main” 
window, check the following, make corrections if 

necessary, and then retry migration: 
The communication between management server (HVM 
Navigator) and the specified server blade is normal. 
Select Migration Service in the left pane, and see if 
Migration Service Status in right pane is “Run.” 
Migration Service Port in the same pane is usable. 

0x00 00000000 0005 01  The specified blade is not found. 

Check the following, make corrections if necessary, and 
then retry migration: 
The specified server blade is present. 
The specified server blade is up and running. 
Communication to the IP address of the specified 
server blade is established. 

0x00 00000000 0006 01  The version isn

’

t matched 

between MMC and MMS. 

Install HVM Navigator again. 

 

 

 

Summary of Contents for HVM Navigator V03-06

























































































































































































































































































































Reviews:

No comments