Hitachi HVM Navigator V03-06 User Manual Download Page 271

Page: 271 / 312

Troubleshooting

6-9

HVM Navigator User's Guide - Migration

Inspect the content of Error Message field.

Figure 6-10 Option window

If the error message refers to Java, check if JRE 7 or higher is installed. If

not, install the latest JRE.

Solution 2: When environment variable to the installed JRE is not set or not

properly set

Set or correct the environment variable to the installed JRE according to

Hitachi Compute Blade HVM Navigator Installation Manual.

Solution 3: When communication between HVM Navigator and HVM is lost
1.

Check if the HVM registered to be managed by HVM Navigator is up and

normally running through HVM screen, host management window of

SC/BSM, or HVM configuration management window of SC/BSM.

If you see no problem in the step above, then inspect the link between the

HVM and HVM Navigator by issuing diagnostic command such as ping from
the management server (HVM Navigator) to the subject HVM. Should you

find any fault, further analyze the cause and then eliminate the cause.

Java version (build) can be confirmed by entering “java -version” from the

command prompt.

Summary of Contents for HVM Navigator V03-06

























































































































































































































































































































Search results

Summary of Contents for HVM Navigator V03-06

Reviews:

Hitachi HVM Navigator V03-06, User Manual, Page: 271 / 312

Search results

Summary of Contents for HVM Navigator V03-06

Reviews: