Hitachi HVM Navigator V03-06 User Manual Download Page 17

Page: 17 / 312

Overview

1-3

HVM Navigator User's Guide - Migration

Table 1-1 Exchangeable hardware and software with Concurrent

Maintenance mode

Hardware/software

Operator

HVM firmware

User

SD card

Maintenance crew

CPU indicating issues

Memory indicating issues

NIC/FC HBA switch which doesn’t support exchanging while the server blade is in

operation

EFI/BIOS firmware

BMC firmware

server blade

There are differences with the application requirements and kinds of

configuration data to migrate, between Shutdown mode and Concurrent
Maintenance mode. Application requirements for Shutdown mode are much

less than those for Concurrent Maintenance mode. When you have an LPAR

migrate on a server blade on a system environment for the first time, it’s
recommended that have the LPAR migrate in Shutdown mode.

Figure 1-2 Differences with application requirements for migration

Application requirements

for Shutdown mode

Application requirements

for Concurrent Maintenance mode

Summary of Contents for HVM Navigator V03-06

























































































































































































































































































































Search results

Summary of Contents for HVM Navigator V03-06

Reviews:

Hitachi HVM Navigator V03-06, User Manual, Page: 17 / 312

Search results

Summary of Contents for HVM Navigator V03-06

Reviews: