manualshive.com logo in svg

Hitachi HVM Navigator V03-06, User Manual, Page: 209 / 312

Share
Download
Hitachi HVM Navigator V03-06 User Manual Download Page 209

 

Migration procedures 

3-113 

HVM Navigator User's Guide - Migration 

Commands for Storage Navigator Modular 2 CLI executed from 

HVM Navigator 

The commands for Storage Navigator Modular 2 CLI which is executed from 

HVM Navigator are shown in the following table. 

Table 3-5 Setting for Password Protection and Account Authentication 

Command 

Use on HVM Navigator 

auunitref 

Retrieve data for registered storage devices. 

auhgwwn -unit [machine type] -refer 

Display data in WWN List in Register Migration WWN 

Setting window. 

[9500V] 
-unit [array unit name] -set -permhg 0 A [migration 
WWPN] [migration WWNN] -gno 001 
[the other machine type] 
-unit [array unit name] -set -permhg 0 A [migration 
WWPN] -gno 001 

Register a migration WWPN to a host group. 
(This command is used when any command with the 
migration WWPN has been executed in the past.) 

[9500V] 
-unit [array unit name] -assign -permhg 0 A [migration 
WWPN] [migration WWNN] 
[the other machine type] 
-unit [array unit name] -assign -permhg 0 A [migration 
WWPN] -gno 001 

Register a migration WWPN to a host group. 
(This command is used when any command with the 
migration WWPN hasn't been executed in the past.) 

[9500V] 
-unit [array unit name] -rm -permhg 0 A [migration WWPN] 

[migration WWNN] -gno 001 
[the other machine type] 
-unit [array unit name] -rm -permhg 0 A [migration 
WWPN]-gno 001 

Remove a migration WWPN from a host group. 

[9500V] 
auhgwwn -unit [array unit name] -chg -rename 0 A 
[migration WWPN] [migration WWNN] -gno 001 -

newwname [nickname] 
[the other machine type] 
auhgwwn -unit [array unit name] -chg -rename 0 A 

[migration WWPN] -gno 001 -newwname [nickname] 

Set a nickname for a migration WWPN. 

auunitadd -ctl[controller No.] [controller IP address] 

Register a storage device to the Storage Navigator 
Modular 2 CLI. 

[AMS, WMS, SMS] 
auconstitute -unit [array unit name] -export -port [file path 

and file name] 

Back up data for host groups. 

[9500V] 
auhgout -unit [array unit name] -file [file path and file 
name] 

Back up data for host groups. 

aulogin -unit [array unit name] 

Log in to a storage device where Password Protection 

is set. 

aulogout -unit [array unit name] 

Log out from a storage device where Password 

Protection is set. 

Summary of Contents for HVM Navigator V03-06

























































































































































































































































































































Reviews:

No comments