background image

Technical Data 

186/299 

PC Cards cifX Compact PCI, Mini PCI, Mini PCIe, PCI-104 | Installation, Operation and Hardware Description  
DOC120205UM53EN | Revision 53 | English | 2019-03 | Released | Public  

© Hilscher, 2008-2019 

10.1.10  CIFX 90E-RE\F and Variants 

CIFX 90E-RE\F  
and Variants

 

Parameter 

Value 

CIFX 90E-RE\F 

1291.100 

CIFX 90E-RE\NHS\F 

1291.108 

CIFX 90E-RE\ET\F 

1291.104 

CIFX 90E-RE\MR\F 

1291.102 

CIFX 90E-RE\MR\ET\F 

1291.106 

CIFX 90E-RE\F\M12 

1291.120 

CIFX 90E-RE\NHS\F\M12 

1291.128 

CIFX 90E-RE\ET\F\M12 

1291.124 

CIFX 90E-RE\MR\F\M12 

1291.122 

Name, Part No. 

CIFX 90E-RE\MR\ET\F\M12 1291.126 

Description 

PC Card cifX Mini PCI Express for Real-Time Ethernet 
Master or Slave (and variants ‚NHS‘ =no heat sink, with 
enlarged temperature range ‚ET’ and/or additional MRAM 
‚MR’) composed of: 
- Basic card CIFX 90E, CIFX 90E\NHS, CIFX 90E\ET, 
CIFX 90E\MR or CIFX 90E\MR\ET with cable connector 
Ethernet X4 

and

  

- Ethernet detached network interface (AIFX-RE)  
- Ethernet M12 detached network interface (AIFX-RE\M12)

Note:

 The device height and the power input of the PC Card cifX 

Mini PCI Express CIFX 90E-RE\F, CIFX 90E-RE\NHS\F, CIFX 
90E-RE\ET\F, CIFX 90E-RE\MR\F and CIFX 90E-RE\MR\ET\F, 
CIFX 90E-RE\F\M12, CIFX 90E-RE\NHS\F\M12, CIFX 90E-
RE\ET\F\M12, CIFX 90E-RE\MR\F\M12 and CIFX 90E-
RE\MR\ET\F\M12 do not comply with the standard specifications.

 

Part 

Function 

Communication Interface with Mini PCI Express and 
Ethernet interface 

Communication 
Controller 

Type netX 

100 

processor 

RAM 

8 MB SDRAM 

FLASH  

4 MB serial Flash EPROM 

Size of the Dual-Port Memory 

64 KByte 

Integrated Memory 

MRAM (only CIFX 90E-RE\MR\F, 
CIFX 90E-RE\MR\ET\F, CIFX 
90E-RE\MR\F\M12 or CIFX 90E-
RE\MR\ET\F\M12) 

128Kbyte (= 64K Words);  

Note:

 Using the cifX Device Driver (from Version 1.1.1.0) 

access to this memory is possible and it can be used as a 
remanent memory. 

Bus Type 

Mini PCI Express, One Lane Port, according to  
[bus spec 2], refer to section 

Overview

, page 165 and 

Pin 

Assignment for Mini PCI Express Bus / SYNC Connector 
(Bootstart), X1/X2

, page 168. 

Transmission Rate 

33 MHz 

Data Access 

DPM or DMA* (Direct Memory Access);  

*CIFX 90E-RE\F from Hardware Revision A,  
CIFX 90E-RE\MR\F from Hardware Revision B,  
CIFX 90E-RE\NHS\F, CIFX 90E-RE\ET\F and CIFX 90E-
RE\MR\ET\F from Hardware Revision 1 

These specifications also apply to the variants with the 
Ethernet M12 detached network interface AIFX-RE/M12. 

System Interface 

Width for the data access to the 
Dual-Port Memory (DPM) 

32-Bit 

CC-Link IE Field Basic Slave 

EtherCAT Master, EtherCAT Slave 

Ethernet 
Communication 

Supported Real-Time Ethernet 
communication systems  
(determined by the loaded 
firmware) 

EtherNet/IP Scanner (Master),  
EtherNet/IP Adapter (Slave), 

Summary of Contents for CIFX Series












































































































































































































































































































Reviews: