hilscher CIFX Series User Manual Download Page 20 | Manualshive

Page: 20 / 299

background image

Introduction

20/299

PC Cards cifX Compact PCI, Mini PCI, Mini PCIe, PCI-104 | Installation, Operation and Hardware Description
DOC120205UM53EN | Revision 53 | English | 2019-03 | Released | Public

© Hilscher, 2008-2019

1.2.3.3

PROFINET IO-Device Firmware Versions V3.4 and V3.13

The PROFINET IO Device firmware was revised and completed and is
available in version 3.13 since the fourth quarter 2018.

Use the PROFINET IO Device firmware in version 3.13 for a new
installation, when you create or develop your application program for the
first time.

If you want to change in an existing system from the PROFINET IO Device
firmware version 3.4 to the version 3.13, note the following guidelines:

1. Customize your application program according to the Migration Guide

PROFINET IO Device, Migration from V3.x to V3.13

.

If you want to change to V3.13, please check in the Migration Guide

PROFINET IO Device, Migration from V3.x to V3.13

which changes are

necessary in the application program in order to use version 3.13.

2. Adjust the configuration of your PROFINET IO Controller device. Use

the new GSDML file in the configuration software of the PROFINET IO
Controller for this:

GSDML-V2.33-HILSCHER-CIFX RE PNS-xxxxxxxx.xml.

3. Update the PROFINET IO Device firmware in your device to version

3.13.

Note also:

•

SYCON.net V1.500.x.x can configure the PROFINET IO Device

firmware V3.4 as well as V3.13

•

The development of the PROFINET IO Device firmware V3.4 will not be

continued, but this firmware version will be delivered furthermore.

On the Communication Solutions DVD, software and manuals relating to
both firmware versions V3.4 and V3.13 are available:

PROFINET IO-Device V3.4

Directory on the DVD \ File:

PROFINET IO-Device V3.13

Directory on the DVD \ File:

Firmware

Firmware\CIFX\cifxpns.nxf Firmware\CIFX\C010D000.nxf

Header

Examples and API\0. Header\Firmware\PROFINET IO
Device V3.4.X

Examples and API\0. Header\Firmware\PROFINET IO
Device V3.13

GSDML

EDS\PROFINET\V3.4.X\GSDML-V2.3-HILSCHER-CIFX
RE PNS-20130225.xml

EDS\PROFINET\Device\V3.13\GSDML-V2.33-
HILSCHER-CIFX RE PNS-xxxxxxxx.xml

Protocol API

Documentation\7. Programming Manuals\EN\3. Protocol
API\PROFINET IO Device V3.4\PROFINET IO Device
Protocol API 13 EN.pdf
TCP IP - Packet Interface API 13 EN.pdf

Documentation\7. Programming Manuals\EN\3.
Protocol API\PROFINET IO Device V3.13\PROFINET
IO Device V3.13 Protocol API 18 EN.pdf
PROFINET IO Device - Migration from Version 3.x to
3.13 MG 09 EN.pdf

Table 8: PROFINET IO-Device Firmware Version 3.4 and 3.13, Header, GSDML and
Protocol API Manual

«
...
18
19
20
21
22
...
»

Summary of Contents for CIFX Series












































































































































































































































































































Reviews:

No comments

Related manuals for CIFX Series

Brand: Ubiquiti Pages: 24

Brand: Ebyte Pages: 8

Brand: Delta Tau Pages: 74

Brand: Intel Pages: 108

Brocade X6-8 Director

Brand: Broadcom Pages: 207

Brand: Cypress Semiconductor Pages: 11

Brand: NC-link Pages: 20

Brand: Rane Pages: 128

Brand: Acard Pages: 34

Brand: Shure Pages: 113

Brand: MSNswitch Pages: 2

Brand: Vega Pages: 12

Brand: Datum Pages: 49

Power System S914

Brand: IBM Pages: 48

Brand: SilverStone Pages: 28

Brand: ASROCK Pages: 173

Brand: Rosewill Pages: 2

Network Scanning Unit A

Brand: Ricoh Pages: 206

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands