hilscher CIFX Series User Manual Download Page 172

Page: 172 / 299

Technical Data

172/299

10 Technical Data

10.1 Technical Data PC Cards cifX

Note:

All technical data are temporarily and can be altered without notice.

10.1.1 CIFX

80-RE

CIFX 80-RE

Parameter

Value

Name, Part No.

CIFX 80-RE

1280.100

Description

PC Card cifX Compact PCI for Real-Time Ethernet Master
or Slave

Part

Function

Communication interface with Compact PCI and Ethernet
interface

Communication
Controller

Type netX

100

processor

RAM

8 MB SDRAM

FLASH

4 MB serial Flash EPROM

Integrated Memory

Size of the Dual-Port Memory

64 KByte

Bus Type

Compact PCI, according to [bus spec 4], refer to section

Overview

, page 165.

Transmission Rate

33 MHz

Data Access

DPM or DMA (Direct Memory Access)

System Interface

Width for the data access to the
Dual-Port Memory (DPM)

32-Bit

CC-Link IE Field Basic Slave
EtherCAT Master, EtherCAT Slave
EtherNet/IP Scanner (Master),
EtherNet/IP Adapter (Slave),

Open Modbus/TCP

POWERLINK Controlled Node/Slave
PROFINET IO-Controller (Master),
PROFINET IO-Device (Slave)

Sercos Master, Sercos Slave

Supported Real-Time Ethernet
communication systems
(determined by the loaded
firmware)

VARAN Client (Slave)

Ethernet
Communication

Ethernet Frame Types

Ethernet II

Transmission rate

100 MBit/s,
10 MBit/s (depending on loaded firmware)

Interface Type

100 BASE-TX,
10 BASE-T (depending on loaded firmware),
refer to section

Ethernet Interface

, page 151.

Galvanic Isolation

isolated

Isolation Voltage

1000 VDC (tested for 1 minute)

Half duplex/Full duplex

depending on loaded firmware,
supported (at 100 MBit/s)

Auto-Negotiation

depending on loaded firmware

Auto-Crossover

depending on loaded firmware

Connector

2* RJ45 Socket

Ethernet Interface

Channel 0 and 1

With loaded EtherCAT Master firmware only the RJ45
channel 0 can be used, channel 1 is deactivated.
Beginning with the EtherCAT Master firmware version 3

Summary of Contents for CIFX Series












































































































































































































































































































Search results

Summary of Contents for CIFX Series

Reviews:

Related manuals for CIFX Series

Brands by name

Popular brands

hilscher CIFX Series, User Manual

Search results

Summary of Contents for CIFX Series

Reviews:

Related manuals for CIFX Series

Brands by name

Popular brands