manualshive.com logo in svg

Harris Platinum Z2 CD, Manual

The Harris Platinum Z2 CD is a top-of-the-line electronic device designed to enhance your entertainment experience. With its advanced features and user-friendly interface, this product promises seamless performance. You can easily access a free digital manual for the Harris Platinum Z2 CD on our website, making it convenient to set up and operate this exceptional device.

Share
Download
background image

888-2406-002

3

WARNING: Disconnect primary power prior to servicing.

Table of Contents

PA Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Directional Coupler Removal and Replacement . . . . . 5-7

Typical Coupling Ratios . . . . . . . . . . . . . . . . . . . . . . 5-7

Setting Maximum Power Limits . . . . . . . . . . . . . . . . . 5-8
Setting FWD PWR to Display 100%  . . . . . . . . . . . . . 5-9
Setting Life Support Power Level . . . . . . . . . . . . . . . . 5-9
Forward Power Calibration . . . . . . . . . . . . . . . . . . . . 5-10
Reflected Power Calibration . . . . . . . . . . . . . . . . . . . 5-13
PC Board Replacement Procedures . . . . . . . . . . . . . . 5-15

Replacement of the Life Support Board . . . . . . . . . 5-15
Replacing the Power Supply Controller Board. . . . 5-17
Replacing a PA Controller Board . . . . . . . . . . . . . . 5-17
Replacing the Master Controller Board  . . . . . . . . . 5-18

Replacement Using EEPROM U39 From

Old Board  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18

Replacing EEPROM U39 . . . . . . . . . . . . . . . . . . . . 5-19

System Configuration and Calibration  . . . . . . . . . . . 5-21

Configuration  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21
Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-23

Removing and Replacing Firmware ICs . . . . . . . . . . 5-23

6  Troubleshooting

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Power Amplifier Repair. . . . . . . . . . . . . . . . . . . . . . . . 6-2

Transmitter Power vs. Module Failures  . . . . . . . . . . 6-2

Multiple PA Failures in a Foursome. . . . . . . . . . . . 6-3

Software Revision . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
System Reset - TX_RESTART . . . . . . . . . . . . . . . . . . 6-4

3 Strike Routine  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

Diagnostics Display Menu Tree  . . . . . . . . . . . . . . . . . 6-6
Fault Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6

Front Panel Fault LED  . . . . . . . . . . . . . . . . . . . . . . . 6-7
Fault Reset  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Abbreviations Used In Fault Reporting  . . . . . . . . . . 6-7
Fault Listing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8

Self Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8

System Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9

PA Muting Test. . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
PA_ISO Resistor and Thermistor Test . . . . . . . . . 6-10
PA RF Switch Test . . . . . . . . . . . . . . . . . . . . . . . . 6-11

Hardware Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11

General Troubleshooting Tips . . . . . . . . . . . . . . . . . . 6-12

Foldback Conditions . . . . . . . . . . . . . . . . . . . . . . . . 6-12
Turning the Transmitter ON with No Power

Output  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12

Asterisk and Pound Signs(*, #)  . . . . . . . . . . . . . . . 6-12

Master Controller Faults . . . . . . . . . . . . . . . . . . . . . . 6-13

THERMISTOR, Fault  . . . . . . . . . . . . . . . . . . . . . . 6-13
EEPROM_DEF, EEPROM U39 Default Load  . . . 6-13
REF_WARNING, +5V Reference Warning. . . . . . 6-14
MSTR_REF, +5V Reference Fault. . . . . . . . . . . . . 6-14
RFL_PWR, Reflected Power Fault  . . . . . . . . . . . . 6-14
INTLK, External Interlock Fault  . . . . . . . . . . . . . . 6-15
FAILSAFE, Interlock Fault  . . . . . . . . . . . . . . . . . . 6-15
POWER_FAIL, Fault . . . . . . . . . . . . . . . . . . . . . . . 6-15
LOW_AIR, Fault . . . . . . . . . . . . . . . . . . . . . . . . . . 6-15
UPS, Uninterruptable Power Supply Fault. . . . . . . 6-16
CPLR_NC, Forward Directional Coupler Cable Not 

Connected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-16

IPA_#_MUTE, Fault  . . . . . . . . . . . . . . . . . . . . . . . 6-16
IPA_#_LOW, Fault . . . . . . . . . . . . . . . . . . . . . . . . . 6-16
IPA_#_OC, Fault  . . . . . . . . . . . . . . . . . . . . . . . . . . 6-16
IPA_TW, IPA Temperature Warning  . . . . . . . . . . . 6-17
IPA_OT, Fault. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-17
IPA_#_OUT, Fault . . . . . . . . . . . . . . . . . . . . . . . . . 6-17
IPA_LOAD, Fault. . . . . . . . . . . . . . . . . . . . . . . . . . 6-17
PSC#_COMM, Fault  . . . . . . . . . . . . . . . . . . . . . . . 6-17
PAC#_COMM, Fault . . . . . . . . . . . . . . . . . . . . . . . 6-17
AMB_WARNING, Ambient Temperature Warning6-18
AMB_TEMP, Ambient Temperature Fault  . . . . . . 6-18
ISO_BZ, Over-Temperature . . . . . . . . . . . . . . . . . . 6-18

System ISO Foldback  . . . . . . . . . . . . . . . . . . . . . 6-18
System ISO Overload (Fault)  . . . . . . . . . . . . . . . 6-19

EXC#_FAULT, Fault  . . . . . . . . . . . . . . . . . . . . . . . 6-19
EXC#_LOW, Fault . . . . . . . . . . . . . . . . . . . . . . . . . 6-19
EXC#_AFC Fault . . . . . . . . . . . . . . . . . . . . . . . . . . 6-19

PA Signal Tracing . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-20
PA Controller Faults . . . . . . . . . . . . . . . . . . . . . . . . . 6-21

General PA Troubleshooting  . . . . . . . . . . . . . . . . . 6-21
PA#_OC, PA Over-Current Fault . . . . . . . . . . . . . . 6-21
PA Current Foldback  . . . . . . . . . . . . . . . . . . . . . . . 6-21
PA#_UC, PA Under-Current Fault . . . . . . . . . . . . . 6-22
PA#_MUTE_FLT, PA Mute Fault  . . . . . . . . . . . . . 6-22
PA#_OT, PA Over-Temperature Fault  . . . . . . . . . . 6-22
PA#_OUT, PA Out Fault  . . . . . . . . . . . . . . . . . . . . 6-22
PA#_ISO, PA ISO Over-Temperature Fault . . . . . . 6-22
PA_ISO_OT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-23
PA_ISO_LOW, Fault  . . . . . . . . . . . . . . . . . . . . . . . 6-23
PA_ISO_SW, Fault . . . . . . . . . . . . . . . . . . . . . . . . . 6-24
Combiner ISO Faults  . . . . . . . . . . . . . . . . . . . . . . . 6-24
PAC#_REF, +5V Reference Fault  . . . . . . . . . . . . . 6-24
PAC#_VOLTS, Power Supply Fault  . . . . . . . . . . . 6-24
PAC#_-15V, PA Controller PS Fault  . . . . . . . . . . . 6-24

Summary of Contents for Platinum Z2 CD





































































































































































































Reviews:

No comments

Related manuals for Platinum Z2 CD

BAPI Wireless Room Temperature Transmitter Installation And Operating Instructions preview
Wireless Room Temperature Transmitter
Brand: BAPI Pages: 2
SkyGuardTWX 978 UAT/1090 ES Setup preview
978 UAT/1090 ES
Brand: SkyGuardTWX Pages: 2
M-system 10PA Instruction Manual preview
10PA
Brand: M-system Pages: 2
Badger Meter Orion Universal 1 Transmitter Installation Data preview
Orion Universal 1 Transmitter
Brand: Badger Meter Pages: 2
NIVELCO NIVOCAP C-200 User And Programming Manual preview
NIVOCAP C-200
Brand: NIVELCO Pages: 36
TQ-Systems MODUL NO. ONE Operating Instruction preview
MODUL NO. ONE
Brand: TQ-Systems Pages: 20
MYE MWCS-AT9-LFA Manual preview
MWCS-AT9-LFA
Brand: MYE Pages: 5
MICROTRONIX HSMC Daughter Card User Manual preview
HSMC Daughter Card
Brand: MICROTRONIX Pages: 10
TFA 30.3114 Manual preview
30.3114
Brand: TFA Pages: 5
LYNXTechnik Yellobrik OTR 1440 Quick Reference preview
Yellobrik OTR 1440
Brand: LYNXTechnik Pages: 2
Lynx yellobrik OTX 1410 Quick Reference preview
yellobrik OTX 1410
Brand: Lynx Pages: 2
Lynx yellobrik OTR 1840-1 Quick Reference preview
yellobrik OTR 1840-1
Brand: Lynx Pages: 2
Industrial Controls IP500AC Installation, Operation And Maintenance Instructions preview
IP500AC
Brand: Industrial Controls Pages: 5
Browning LTD Installation And Operating Insctructions preview
LTD
Brand: Browning Pages: 12
Terasic HSMC-NET User Manual preview
HSMC-NET
Brand: Terasic Pages: 32
ViaLite LSX-Ex-HB-2 User Manual preview
LSX-Ex-HB-2
Brand: ViaLite Pages: 16
WIKA CPT6020 Operating Instructions Manual preview
CPT6020
Brand: WIKA Pages: 34
Stryker SR440-HP User Manual preview
SR440-HP
Brand: Stryker Pages: 3

Brands by name

Popular brands

Load more brands