EdgeM
Parts Needed:
¾
es that make up one EdgeMaster
TM
eMa
chine Quilter.
¾
¾
es that make up one EdgeMaster
TM
eMa
chine Quilter.
¾
¾
aster
TM
Assembly
2 – Base Plate w/ Pre-installed sleeve
2
–
Lever
2 – Clamping Bracket
There are three wood piecc
(for side tension). There are two
Place the Lever into the “U”
shape of the Clamping Bracket,
and put the opposite end through
the slot in the Base Plate.
With your fabric completely
installed, you can install the
EdgeMasters
TM
onto the front
and middle rails (one on each
side
o ends of the
rail. NOTE! Be
side, and move
n o
ines, it ma
TM
if your
your quilt.
(for side tension). There are two
Place the Lever into the “U”
shape of the Clamping Bracket,
and put the opposite end through
the slot in the Base Plate.
With your fabric completely
installed, you can install the
EdgeMasters
TM
onto the front
and middle rails (one on each
side
o ends of the
rail. NOTE! Be
side, and move
n o
ines, it ma
TM
if your
your quilt.
Edg
sters
TM
included with your Grace Ma
Edg
sters
TM
included with your Grace Ma
of the quilt).
To do so, simply angle them until the tw
mping Bracket fit over the front and middle
t).
of the quilt).
To do so, simply angle them until the tw
mping Bracket fit over the front and middle
t).
leader cloth
dowel
clamping lever
Edge Master Assembly
base
¾
Cla
sure the pre-installed cloth sleeve is facing toward the quilt (see
righ
¾
To
you
rs of
Now you can achieve perfect side tension throughout your enti
area. Gently pull the EdgeMaster
TM
toward the out
¾
Cla
sure the pre-installed cloth sleeve is facing toward the quilt (see
righ
¾
To
you
rs of
Now you can achieve perfect side tension throughout your enti
area. Gently pull the EdgeMaster
TM
toward the out
use the EdgeMasters
TM
, pin the cloth sleeve to the edge of
r quilt (about ¼” in). Be sure the pins go through all three
use the EdgeMasters
TM
, pin the cloth sleeve to the edge of
r quilt (about ¼” in). Be sure the pins go through all three
laye
your quilt. Use three or four straight pins for this.
laye
your quilt. Use three or four straight pins for this.
re work
the
n the
re work
the
n the
Lever down so that the Base Plate and Clamping Bracket tighte
rail. There is no need to over-tighten the lever. It will hold its position.
Note! Due to the difference in some sewing mach
necessary to make wider sleeves for your EdgeMaster
sewing machine hits into the Clamping Bracket of the
EdgeMaster
TM
before you reach the stops or end of
Carriage Stop Assembly
Lever down so that the Base Plate and Clamping Bracket tighte
rail. There is no need to over-tighten the lever. It will hold its position.
Note! Due to the difference in some sewing mach
necessary to make wider sleeves for your EdgeMaster
sewing machine hits into the Clamping Bracket of the
EdgeMaster
TM
before you reach the stops or end of
Carriage Stop Assembly
Parts Needed: 2 – Carria
1/4 wing
nut
1/4 flat
washer
y be
y be
ge Stop
2 – ¼” x 1 ½” Carriage Bolt
2 – ¼” Flat washers
2 – ¼” Wing Nuts
(Hardware is in packet marked “M”)
¾
Place the ¼” x 1 ½” carriage bolt up through the bottom of the
Table Top (left and right).
¾
As it comes up through the table place the bolt through the slot
¾
Place the flat side toward the carriage assembly (pointed side away).
of the Carriage Stop.
¾
Then put a flat washer and wing nut on the end of the bolt and
leave somewhat loose.
¾
With your carriage rolling on its tracks, you can determine exactly
where to put your stops.
1/4 X 1/2
ca
bolt
38
clamping
bracket
1
rriage
