GEA ECOVENT Operating Instructions Manual Download Page 19

Page: 19 / 128

2.9 Safety signs

The safety symbols listed below are attached to the valve.
The position of the applicable safety symbols on the valve are shown in an overview,

see

3.1.3 Signs

Warning signs

General warning sign

Hazard for persons, conveyed by the additional sign.

Warning, risk of hand injuries

Hazard posed by closing mechanical components on the valve.

Warning, spring tension

Hazard posed by spring tension. Do not open the actuator.

Explosion-hazarded zones warning

Special explosion protection sign

2.10 Emergency measures

In case of any emergencies on the valve, the operating regulations must be observed

and the following actions implemented.

Fire

●

Call local specialists

●

Use extinguishing agents as outlined in the operating regulations

●

Exit the hazard zone

●

Warn individuals that are endangered

Injuries

●

Administer first aid

●

Call local emergency services

2.9 Safety signs - 19 / 128

Summary of Contents for ECOVENT
































































































































Search results

Summary of Contents for ECOVENT

Reviews:

Related manuals for ECOVENT

Brands by name

Popular brands

GEA ECOVENT, Operating Instructions Manual

Search results

Summary of Contents for ECOVENT

Reviews:

Related manuals for ECOVENT

Brands by name

Popular brands