GEA ECOVENT Operating Instructions Manual Download Page 52

Page: 52 / 128

●

Articulated face spanner with journal 4 mm

WARNING

Spring tension in the valve (NC)

Danger of injury when opening the clamp connections on the actuator or on the

housing as the released spring pretension will suddenly lift the actuator.

●

Therefore, release the spring tension before detaching the clamp connection by

pressurising the actuator with compressed air at max. 8 bar.

Release the Philips screws (25) and
take off the cap (7).

Pressurize the actuator – with com-
pressed air (max. 8 bar) - by activating
the solenoid valve Y1 at the manual
operation element S.

The valve disk is raised.

Remove hinged clamps (43) between the upper and middle housing.

52 / 128 - 9.5 Removing the valve

0000000607 - 002 - EN-GB

Summary of Contents for ECOVENT
































































































































Search results

Summary of Contents for ECOVENT

Reviews:

Related manuals for ECOVENT

Brands by name

Popular brands

GEA ECOVENT, Operating Instructions Manual

Search results

Summary of Contents for ECOVENT

Reviews:

Related manuals for ECOVENT

Brands by name

Popular brands