GEK-105593C
62
COIL 2:
•
Repeat the previous test for coil 2. Positive should be applied to terminal F7 and negative to terminal E8.
The signal to be checked is "Coil 2 DC Supply Failure".
6.30. MONITORING TRIP CIRCUITS : COIL FAILURE
(Only for models with expansion board)
COIL 1:
•
Short-circuit terminals E5, F6 and E6 (common).
•
Apply nominal minimum voltage (38 Vdc for "A" models and 88 Vdc for "H" models) to the voltage
supervision input for coil 1. Positive is applied to terminal F5 and the negative to terminal E6.
•
Check using GE_LOCAL software that the "Coil 1 Continuity Failure" signal in the internal Status of the
relay is not active.
•
Remove the short-circuit between terminals E5 and E6.
•
The "Coil 1 Continuity Failure" signal will not become active.
•
Remove the short-circuit between terminals F6 and E6.
•
After 1 sec, the "Coil 1 Continuity Failure" signal will become active.
COIL 2:
•
Repeat the previous test for coil 2. Positive is applied to terminal F7 and negative to terminal E8. The
terminals corresponding to terminals E5, F6 and E6 will be E7, F8 and E8 respectively. The signal to be
checked is "Coil 2 Continuity Failure"
Table 11. Customer’s settings
Description
MMI/GE-LOCAL
USER VALUES
General Settings Group
GENERAL SETTINGS
Relay status
RELAY STATUS
Identification
IDENTIFICAT:
Frequency
FREQUENCY
Rated Voltage
NOMINAL VOLTAGE
CT Phase Ratio
PHASE CT RATIO
CT Ground Ratio
GROUND CT RATIO
VT Line Ratio
LINE VT RATIO
VT Busbar Ratio
BUS VT RATIO
Demand Time
DEMAND TIME
Phase rotation selection
PHASE ROTATION
Breaker Settings Group
BREAKER SETTINGS
Breaker Number
BREAKER NUMBER
Fail to Open time
t FAIL TO OPEN
Fail to Close time
t TAIL TO CLOSE
Accumulable I2t Limit
KI2T LIMIT
Intg I2t Time selector
KI2T OP. MODE
I2t Integr. time
KI2T INT. TIME
Maximum trips in 1 hour
MAX TRIPS 1h
Active Table Settings
ACTIVE TABLE SET
# of Active Settings Table
ACTIVE TABLE
Cold pick-up permission
CLP PERMISSION
Change to Table 3 time
t CHANGE TABLE
Return from Table 3 time
t RETURN TABLE
Oscillography Mask
OSCILLOS MASK
Number of pre-fault cycles
PREFAULT CYCLES
Oscillo. triggers :
Pick-up 51 PT
51PT PICKUP
Pick-up 51 NT
51NT PICKUP
Summary of Contents for SMOR-B GEK 105593C
