Galaxy Control Systems 635 Series, Installation/Configuration Manual

Page: 48 / 212

635-SERIES HARDWARE M ANUAL
Chapter-Page
2-3
Table 22: SET THE TERMINATION JUMPERS FOR EACH SECTION ................................................................. 2-31
Table 23: SET THE PASS-THRU JUMPERS FOR EACH SECTION
..................................................................... 2-32
Table 24: BINARY ADDRESS TABLE FOR 635-DRM ............................................................................................ 2-33
Table 25: BINARY ADDRESS TABLE FOR OUTPUT RELAY BOARD
................................................................. 2-38
Table 26: WIRING PINOUT FROM 635-DSI TO FIRST RELAY BOARD ............................................................... 2-42
Table 27: WIRING PINOUT FROM ONE RELAY BOARD TO NEXT RELAY BOARD
.......................................... 2-42
Table 28: BINARY DIPSWITCH SETTINGS FOR INPUT BOARD ......................................................................... 2-46
Table 29: WIRING PINOUT FROM THE 635-DSI TO FIRST INPUT BOARD
........................................................ 2-51
Table 30: WIRING PINOUT FROM ONE INPUT BOARD TO NEXT INPUT BOARD ............................................. 2-51
Table 31: FLASH VERISON CHART
....................................................................................................................... 2-62
Table 32: WIRING DISTANCES FOR HARDWARE ................................................................................................ 2-67
Table 33: Software Setup - Process for 600 Loops are as follows
..................................................................... 2-81
LIST OF FIGURES FOUND IN THIS CHAPTER
Figure 8 – Illustration of UL-Listed Power Supply and Transformer .................................................................... 2-6
Figure 9 – 6xx-series Controller Mounting Diagram ............................................................................................ 2-13
Figure 10 – Controller Wiring Harness: ................................................................................................................. 2-14
Figure 11 – Diagram of CPU Power and Tamper Connectors: ............................................................................ 2-15
Figure 12 – 635 CPU Warning Circuits: “A/C Fail”, “Low Battery”, and “Tamper” ........................................... 2-16
Figure 13 – Wiring Power Connector on 635 DRM: .............................................................................................. 2-17
Figure 14 – Installing CPU (with bracket against back of cabinet) ..................................................................... 2-18
Figure 15 – 635 DRM Board Features: ................................................................................................................... 2-19
Figure 16 – BINARY DIPSWITCH for DRM Board ID ............................................................................................ 2-23
Figure 17 – Installing a DRM Board with bracket against back of cabinet: ....................................................... 2-24
Figure 18 – 600 DIO Board Features: ..................................................................................................................... 2-25
Figure 19 – Installing a DIO Board with bracket against back of cabinet: ......................................................... 2-26
Figure 20 – 635 DSI Board Features: ..................................................................................................................... 2-27
Figure 21 – Examples using Termination Resistance with the 635 DSI Board: ................................................ 2-31
Figure 22 – Using Pass-thru Jumpers on the 635 DSI Board: ............................................................................. 2-32
Figure 23 – BINARY DIPSWITCH for DSI Board ID .............................................................................................. 2-33
Figure 24 – Installing a DSI Board with bracket against back of cabinet: ......................................................... 2-34
Figure 25 – 635 Output Board Features: ............................................................................................................... 2-35
Figure 26 – Example of Relay Boards in Main Panel for General Purpose Output Relay (ORM) .................... 2-36
Figure 27 – Example of Relay Boards Installed in a Separate Panel .................................................................. 2-37
Figure 28 – Example of Single Layer vs. Stacked Install (SEE PART 4.5.3 FOR EXACT INSTRUCTIONS) .... 2-37
Figure 29 – Relay Board Installation Options (Single Layer vs. Stacked) ......................................................... 2-39
Figure 30 – 635-Relay Board: Wiring the Relay Terminals .................................................................................. 2-40
Figure 31 – 635-Relay Board: Wiring the Power Input ......................................................................................... 2-40
Figure 32 – Relay Board Installation (on the 635-DSI Board’s RS-485 Multidrop) ............................................ 2-41
Figure 33 – 635-Input Module Features ................................................................................................................. 2-43
Figure 34 – Basic Example of Input Boards Installed in the Main Panel ........................................................... 2-44
Figure 35 – Basic Example of Input Boards Installed in a Separate Panel ........................................................ 2-45