background image

 

Contents 

C141-E202-01EN xvii 

Figure 5.2  Execution example of READ MULTIPLE command .....................5-63

 

Figure 5.3  Read Sector(s) command protocol.................................................5-127

 

Figure 5.4  Protocol for command abort ..........................................................5-128

 

Figure 5.5  WRITE SECTOR(S) command protocol.......................................5-130

 

Figure 5.6

 

Protocol for the command execution without data 
transfer ...........................................................................................5-132

 

Figure 5.7  Normal DMA data transfer ............................................................5-133

 

Figure 5.8  Ultra DMA termination with pull-up or pull-down .......................5-145

 

Figure 5.9  PIO data transfer timing.................................................................5-146

 

Figure 5.10  Multiword DMA data transfer timing (mode 2) ............................5-147

 

Figure 5.11  Initiating an Ultra DMA data in burst............................................5-148

 

Figure 5.12  Sustained Ultra DMA data in burst................................................5-152

 

Figure 5.13  Host pausing an Ultra DMA data in burst .....................................5-153

 

Figure 5.14  Device terminating an Ultra DMA data in burst............................5-154

 

Figure 5.15  Host terminating an Ultra DMA data in burst ...............................5-155

 

Figure 5.16  Initiating an Ultra DMA data out burst..........................................5-156

 

Figure 5.17  Sustained Ultra DMA data out burst..............................................5-157

 

Figure 5.18  Device pausing an Ultra DMA data out burst................................5-158

 

Figure 5.19  Host terminating an Ultra DMA data out burst .............................5-159

 

Figure 5.20  Device terminating an Ultra DMA data out burst..........................5-160

 

Figure 5.21  Power-on Reset Timing .................................................................5-161

 

 

Figure 6.1  Response to power-on ........................................................................6-3

 

Figure 6.2  Response to hardware reset................................................................6-4

 

Figure 6.3  Response to software reset.................................................................6-5

 

Figure 6.4  Response to diagnostic command ......................................................6-6

 

Figure 6.5  Sector slip processing ......................................................................6-10

 

Figure 6.6  Automatic alternating processing ....................................................6-11

 

Figure 6.7  Data buffer structure ........................................................................6-12

 

 

 

Summary of Contents for MHU2100AT























































































































































































































































































Reviews: