manualshive.com logo in svg

Fujitsu MHU2100AT, Product Manual, Page: 127 / 278

Share
Download
Fujitsu MHU2100AT Product Manual Download Page 127

5.3  Host Commands

 

C141-E202-01EN 5-51 

• 

Off-line data collection capability 

Indicates the method of off-line data collection carried out by the drive.  If the off-
line data collection capability is 0, it indicates that off-line data collection is not 
supported. 

 

Table 5.12  Off-line data collection capability 

Bit Meaning 

0 

If this bit is 1, it indicates that the SMART EXECUTE OFF-
LINE IMMEDATE sub-command (FR register = D4h) is 
supported. 

1 Vendor 

unique 

2 

If this bit is 1, it indicates that acquisition of off-line data 
under execution is aborted when a new command is received. 

3 

If this bit is 1, it indicates that the SMART Off-line Read 
Scanning Technology is supported. 

4 

If this bit is 1, it indicates that the SMART Self-test function 
is supported. 

5 

If this bit is 1, it indicates that the SMART Conveyance Self-
test is supported. 

6 

If this bit is 1, it indicates that the SMART Selective Self-
test is supported. 

7 Reserved 

bits 

 

• 

Failure prediction capability flag 

 

Table 5.13  Failure prediction capability flag 

Bit Meaning 

0 

If this bit is 1, it indicates that the attribute value is saved on 
media before the drive enters the power save mode. 

1 

If this bit is 1, it indicates that the attribute value is saved 
automatically after the pre-set operation of the drive. 

2 to 15 

Reserved bits 

 

Summary of Contents for MHU2100AT























































































































































































































































































Reviews:

No comments