Fujitsu MHU2100AT Product Manual Download Page 247 | Manualshive

Page: 247 / 278

background image

6.3 Defect Processing

C141-E202-01EN 6-9

6.2.2 Power commands

The following commands are available as power commands.

•

IDLE

•

IDLE IMMEDIATE

•

STANDBY

•

STANDBY IMMEDIATE

•

SLEEP

•

CHECK POWER MODE

•

SET FEATURES (APM setting)

6.3 Defect Processing

This device performs alternating processing where the defective sector is
alternated with the spare area depending on media defect location information.
The media defect location information is registered in the system space specified
for the user area according to the format at shipment of the media from the plant.

6.3.1 Spare area

The following type of area is prepared as the spare area in user areas:

1) Spare cylinder for alternate assignment: This cylinder is used during

automatic alternating processing for defective sector. More than 2000
sectors/drive.

«
...
245
246
247
248
249
...
»

Summary of Contents for MHU2100AT























































































































































































































































































Reviews:

No comments

Related manuals for MHU2100AT

Brand: Omlet Pages: 4

Brand: AIC Pages: 88

TS7650 PROTECTIER DEDUPLICATION APPLIANCE

Brand: IBM Pages: 218

Brand: Maxtor Pages: 73

Brand: JetStor Pages: 71

Brand: Swissbit Pages: 11

Barracuda 180 Family

Brand: Seagate Pages: 2

TotalStorage Network Attached Storage 300G

Brand: IBM Pages: 86

AltaVault System

Brand: NetApp Pages: 2

Brand: Dot Hill Systems Pages: 134

Brand: U-Line Pages: 6

Brand: Western Digital Pages: 2

Brand: Digital Equipment Pages: 70

Brand: J.Burrows Pages: 13

SolarGuard PB00100R3

Brand: ClearSpan Pages: 41

Brand: Echostreams Pages: 3

Brand: Royalcraft Pages: 33

Brand: Renkforce Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands