manualshive.com logo in svg

Fujitsu MHU2100AT, Product Manual, Page: 99 / 278

Share
Download
Fujitsu MHU2100AT Product Manual Download Page 99

5.3  Host Commands

 

C141-E202-01EN 5-23 

(3)  READ LONG (X’22’ or X’23’)  

This command operates similarly to the READ SECTOR(S) command except that 
the device transfers the data in the requested sector and the ECC bytes to the host 
system. The ECC error correction is not performed for this command. This 
command is used for checking ECC function by combining with the WRITE 
LONG command.  The READ LONG command supports only single sector 
operation. 

Number of ECC bytes to be transferred is fixed to 4 bytes and cannot be changed 
by the SET FEATURES command. 

 

At command issuance (I/O registers setting contents) 

1F7

H

(CM)  0 0 1 0 0 0 1 R 

1F6

H

(DH) 

x 

L 

x 

DV  Head No. /LBA [MSB] 

1F5

H

(CH) 

1F4

H

(CL) 

1F3

H

(SN) 

1F2

H

(SC) 

1F1

H

(FR) 

Cylinder No. [MSB] / LBA 

Cylinder No. [LSB] / LBA 

Sector No. / LBA [LSB] 

01 

xx 

(R: Retry) 

 

At command completion (I/O registers contents to be read) 

1F7

H

(ST) Status 

information 

1F6

H

(DH) 

x 

L 

x 

DV  Head No. /LBA [MSB] 

1F5

H

(CH) 

1F4

H

(CL) 

1F3

H

(SN) 

1F2

H

(SC) 

1F1

H

(ER) 

Cylinder No. [MSB] / LBA 

Cylinder No. [LSB] / LBA 

Sector No. / LBA [LSB] 

xx 

Error information 

 

 

Summary of Contents for MHU2100AT























































































































































































































































































Reviews:

No comments