Fujitsu MHU2100AT Product Manual Download Page 125 | Manualshive

Page: 125 / 278

background image

5.3 Host Commands

C141-E202-01EN 5-49

•

Status Flag

Bit Meaning

0

If this bit is 1, it indicates normal operations are assured with the
attribute when the attribute value exceeds the threshold value.

1

If this bit is 1 (0), it indicates the attribute only updated by an on-
line test (off-line test).

2

If this bit 1, it indicates the attribute that represents performance.

3

If this bit 1, it indicates the attribute that represents an error rate.

4

If this bit 1, it indicates the attribute that represents the number of
occurrences.

5

If this bit 1, it indicates the attribute that can be collected/saved
even if the drive fault prediction function is disabled.

6 to 15

Reserve bit

•

Current attribute value

It indicates the normalized value of the original attribute value. The value
deviates in a range of 01h to 64h (range of 01h to C8h for the ultra ATA CRC
error rate). It indicates that the closer the value is to 01h, the higher the
possibility of a failure. The host compares the attribute value with the threshold
value. If the attribute value is larger than the threshold value, the drive is
determined to be normal.

•

Attribute value for the worst case so far

This is the worst attribute value among the attribute values collected to date. This
value indicates the state nearest to a failure so far.

•

Raw attribute value

Raw attributes data is retained.

•

Off-line data collection status

«
...
123
124
125
126
127
...
»

Summary of Contents for MHU2100AT























































































































































































































































































Reviews:

No comments

Related manuals for MHU2100AT

Brand: Vaillant Pages: 176

Brand: Arrow Storage Products Pages: 36

Brand: Quictent Pages: 24

Brand: Glyph Pages: 7

Brand: Artillian Pages: 3

Brand: garofalo Pages: 20

Brand: Panasonic Pages: 18

Brand: U-Line Pages: 3

Brand: Fujitsu Pages: 40

MHW2060BK - Mobile 60 GB Hard Drive

Brand: Fujitsu Pages: 12

MHX2300BT - Mobile 300 GB Hard Drive

Brand: Fujitsu Pages: 12

MHW2040AT - Mobile 40 GB Hard Drive

Brand: Fujitsu Pages: 278

Brand: Fujitsu Pages: 296

Brand: Fujitsu Pages: 292

MHV2040AT - Hard Drive - 40 GB

Brand: Fujitsu Pages: 280

Brand: Fujitsu Pages: 278

Brand: Fujitsu Pages: 296

Brand: Fujitsu Pages: 320

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands