Fujitsu MHU2100AT Product Manual Download Page 211 | Manualshive

Page: 211 / 278

background image

5.5 Ultra DMA Feature Set

C141-E202-01EN 5-135

Both the host and device perform a CRC function during an Ultra DMA burst. At
the end of an Ultra DMA burst the host sends the its CRC data to the device. The
device compares its CRC data to the data sent from the host. If the two values do
not match the device reports an error in the error register at the end of the
command. If an error occurs during one or more Ultra DMA bursts for any one
command, at the end of the command, the device shall report the first error that
occurred.

5.5.2 Phases of operation

An Ultra DMA data transfer is accomplished through a series of Ultra DMA data
in or data out bursts. Each Ultra DMA burst has three mandatory phases of
operation: the initiation phase, the data transfer phase, and the Ultra DMA burst
termination phase. In addition, an Ultra DMA burst may be paused during the
data transfer phase (see 5.5.3 and 5.5.4 for the detailed protocol descriptions for
each of these phases, 5.6 defines the specific timing requirements). In the
following rules DMARDY- is used in cases that could apply to either
DDMARDY- or HDMARDY-, and STROBE is used in cases that could apply to
either DSTROBE or HSTROBE. The following are general Ultra DMA rules.

a) An Ultra DMA burst is defined as the period from an assertion of DMACK-

by the host to the subsequent negation of DMACK-.

b) A recipient shall be prepared to receive at least two data words whenever it

enters or resumes an Ultra DMA burst.

5.5.3 Ultra DMA data in commands

5.5.3.1 Initiating an Ultra DMA data in burst

The following steps shall occur in the order they are listed unless otherwise
specifically allowed (see 5.6.3.1 and 5.6.3.2 for specific timing requirements):

1) The host shall keep DMACK- in the negated state before an Ultra DMA burst

is initiated.

2) The device shall assert DMARQ to initiate an Ultra DMA burst. After

assertion of DMARQ the device shall not negate DMARQ until after the first
negation of DSTROBE.

3) Steps (3), (4) and (5) may occur in any order or at the same time. The host

shall assert STOP.

4) The host shall negate HDMARDY-.

5) The host shall negate CS0-, CS1-, DA2, DA1, and DA0. The host shall keep

CS0-, CS1-, DA2, DA1, and DA0 negated until after negating DMACK- at
the end of the burst.

6) Steps (3), (4) and (5) shall have occurred at least t

ACK

before the host asserts

DMACK-. The host shall keep DMACK- asserted until the end of an Ultra
DMA burst.

«
...
209
210
211
212
213
...
»

Summary of Contents for MHU2100AT























































































































































































































































































Reviews:

No comments

Related manuals for MHU2100AT

LaCie Ethernet Big Disk

Brand: LaCie Pages: 16

4BIG QUADRA USB 3.0

Brand: LaCie Pages: 41

5big - Network NAS Server

Brand: LaCie Pages: 9

Brand: LaCie Pages: 14

Brand: LaCie Pages: 13

Brand: LaCie Pages: 29

Brand: LaCie Pages: 4

Taylor-Wharton XL-65

Brand: Harsco Pages: 26

Brand: IBM Pages: 2

Brand: Husky Pages: 4

Barracuda 7200.7 ST3120025A

Brand: Seagate Pages: 58

Brand: 7-BIT Pages: 8

Brand: SanDisk Pages: 7

1 GB Microdrive Storage Card

Brand: IBM Pages: 2

LITTLE DISK USB 2.0

Brand: LaCie Pages: 23

Brand: Alphacool Pages: 2

Brand: SANHO Pages: 24

Brand: IBM Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands