Fujitsu MHU2100AT Product Manual Download Page 261 | Manualshive

Page: 261 / 278

background image

C141-E202-01EN GL-1

Glossary

Actuator

Head positioning assembly. The actuator consists of a voice coil motor and head
arm. If positions the read-write (R-W) head.

AT bus

A bus between the host CPU and adapter board

ATA (AT Attachment) standard

The ATA standard is for a PC AT interface regulated to establish compatibility
between products manufactured by different vendors. Interfaces based on this
standard are called ATA interfaces.

BIOS standard for drives

The BIOS standard collectively refers to the parameters defined by the host,
which, for example, include the number of cylinders, the number of heads, and
the number of sectors per track in the drive. The physical specifications of the
drive do not always correspond to these parameters.

The BIOS of a PC AT cannot make full use of the physical specifications of these
drivers. To make the best use of these drives, a BIOS that can handle the standard
parameters of these drives is required.

Command

Commands are instructions to input data to and output data from a drive.
Commands are written in command registers.

Data block

A data block is the unit used to transfer data. A data block normally indicates a
single sector.

DE

Disk enclosure. The DE includes the disks, built-in spindle motor, actuator,
heads, and air filter. The DE is sealed to protect these components from dust.

Master (Device 0)

The master is the first drive that can operate on the AT bus. The master is daisy-
chained with the second drive which can operate in conformity with the ATA
standard.

«
...
259
260
261
262
263
...
»

Summary of Contents for MHU2100AT























































































































































































































































































Reviews:

No comments

Related manuals for MHU2100AT

Brand: Yardmaster Pages: 48

Brand: U-Line Pages: 5

Brand: Premio Pages: 3

Ultrastar Serv24 S2122-N24-4

Brand: HGST Pages: 36

Recessed Mounted Pan Door Medicine Cabinets 935/936

Brand: NuTone Pages: 1

DiskStation DS214play

Brand: Synology Pages: 16

Brand: Eneo Pages: 12

Beside Storage Pantry

Brand: Haworth Pages: 6

Brand: Oracle Pages: 268

Brand: Argus Pages: 1

Memorator Pro 5xHS

Brand: Kvaser Pages: 27

Brand: Fujitsu Pages: 40

ETERNUS2000 100

Brand: Fujitsu Pages: 21

Brand: Fujitsu Pages: 90

Brand: Fujitsu Pages: 12

Brand: Fujitsu Pages: 14

ETERNUS LT40 S2

Brand: Fujitsu Pages: 110

ETERNUS Multipath Driver V2

Brand: Fujitsu Pages: 140

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands