Fujitsu MHU2100AT Product Manual Download Page 240 | Manualshive

Page: 240 / 278

background image

Operations

6-2 C141-E202-01EN

6.1 Device Response to the Reset

This section describes how the PDIAG- and DASP- signals responds when the
power of the IDD is turned on or the IDD receives a reset or diagnostic command.

6.1.1 Response to power-on

After the master device (device 0) releases its own power-on reset state, the
master device shall check a DASP- signal for least 500 ms to confirm presence of
a slave device (device 1). The master device recognizes presence of the slave
device when it confirms assertion of the DASP- signal. Then, the master device
checks a PDIAG- signal to see if the slave device has successfully completed the
power-on diagnostics.

If the master device cannot confirm assertion of the DASP- signal within 500 ms,
the master device recognizes that no slave device is connected.

After the slave device (device 1) releases its own power-on reset state, the slave
device shall report its presence and the result of power-on diagnostics to the
master device as described below:

DASP- signal: Asserted within 450 ms.

PDIAG- signal: Negated within 1 ms and asserted within 30 seconds.

The asserted PDIAG-signal is negated 30 seconds after it is asserted if the
command is not received.

«
...
238
239
240
241
242
...
»

Summary of Contents for MHU2100AT























































































































































































































































































Reviews:

No comments

Related manuals for MHU2100AT

System Storage DS4000

Brand: IBM Pages: 184

DS8000 - ADDITIONAL INFORMATION

Brand: IBM Pages: 5

System Storage TS7600 ProtecTIER Series

Brand: IBM Pages: 132

Brand: IBM Pages: 188

Brand: IBM Pages: 2

Brand: OEM Tools Pages: 4

Brand: SimpleTech Pages: 84

MINI TOOL HOLDER

Brand: tecnotelai Pages: 3

Brand: Transcend Pages: 23

Brand: Icy Box Pages: 24

MERCURY ELITE PRO MINI

Brand: OWC Pages: 8

Brand: Qualstar Pages: 8

SDSDQ-512-A10M - 512MB TransFlash microSD Card Retail...

Brand: SanDisk Pages: 1

Brand: ABSCO SHEDS Pages: 22

PREMIUM STP7736

Brand: Supatool Pages: 3

SPINPOINT MP4 HM250HJ

Brand: Samsung Pages: 1

Brand: Samsung Pages: 16

SpintPoint M8-DVR

Brand: Samsung Pages: 83

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands