Fujitsu MHU2100AT Product Manual Download Page 248 | Manualshive

Page: 248 / 278

background image

Operations

6-10 C141-E202-01EN

6.3.2 Alternating processing for defective sectors

The following two types of technology are used for alternating processing:

(1) Sector slip processing

In this method, defective sectors are not used (thereby avoiding the effects of
defects), and each defective sector is assigned to the next contiguous sector that is
normal.

Depending on the format defined at shipment from the plant, this processing is
performed for defective sectors.

Figure 6.5 shows an example where sector (physical) 5 with cylinder 0 and head 0
is defective.

Sector (physical)

Cylinder 0
Head 0

Defec-
tive
sector

(Not used)

778 779 780

777 778 779

Note: When an access request for sector 5 is issued, physical sector 6 must be

accessed instead of physical sector 5.

Figure 6.5 Sector slip processing

(2) Track slip processing

In this method, defective tracks not used (there by avoiding the effects of defects),
and each defective track is assigned to the next contiguous track that is normal.

Depending on the format defined at shipment from the plant, this processing is
performed for defective tracks.

«
...
246
247
248
249
250
...
»

Summary of Contents for MHU2100AT























































































































































































































































































Reviews:

No comments

Related manuals for MHU2100AT

Brand: Eastwood Pages: 8

Taylor-Wharton XL-65

Brand: Harsco Pages: 26

GLADIATOR PLUS 2

Brand: Asgard Pages: 6

CISCO MDS 9124 - UPDATE FOR SYSTEM STORAGE

Brand: IBM Pages: 37

Fiberglass Underground Storage Tanks

Brand: Xerxes Pages: 31

Brand: Macpower & Tytech Pages: 21

Brand: ClosetMaid Pages: 11

Brand: 7-BIT Pages: 8

USO-HA D500 Series

Brand: STONEFLY Pages: 58

StorageTek SL8500

Brand: Oracle Pages: 59

Brand: Canon Pages: 76

Microdrive RHMD2G

Brand: Sony Pages: 2

Memory Stick PRO DUO MSX-M256S

Brand: Sony Pages: 2

Memory Stick MSA-32A

Brand: Sony Pages: 2

Memory Card DKA-MC10F

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 19

Brand: Sony Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands