Fujitsu MHU2100AT Product Manual Download Page 93

Page: 93 / 278

5.3 Host Commands

C141-E202-01EN 5-17

Notes:

FR: Features

CY: Cylinder

Registers

SC: Sector Count Register

DH: Drive/Head

SN: Sector Number Register

Retry at error

1 = Without retry

0 = With retry

Necessary to set parameters

Y*: Necessary to set parameters under the LBA mode.

Not necessary to set parameters (The parameter is ignored if it is set.)

N*: May set parameters

The device parameter is valid, and the head parameter is ignored.

*O: Option

(customizing)

D*: The command is addressed to the master device, but both the master device

and the slave device execute it.

Do not care

Summary of Contents for MHU2100AT























































































































































































































































































Search results

Summary of Contents for MHU2100AT

Reviews:

Related manuals for MHU2100AT

Brands by name

Popular brands

Fujitsu MHU2100AT, Product Manual

Search results

Summary of Contents for MHU2100AT

Reviews:

Related manuals for MHU2100AT

Brands by name

Popular brands