manualshive.com logo in svg

Fujitsu MHU2100AT, Product Manual, Page: 174 / 278

Share
Download
Fujitsu MHU2100AT Product Manual Download Page 174

Interface 

 

5-98 C141-E202-01EN 

(35)  SECURITY FREEZE LOCK (X’F5’)  

This command puts the device into FROZEN MODE.  The following commands 
used to change the lock function return the Aborted Command error if the device 
is in FROZEN MODE. 

• 

SECURITY SET PASSWORD 

• 

SECURITY UNLOCK 

• 

SECURITY ERASE PREPARE 

• 

SECURITY ERASE UNIT 

• 

SECURITY DISABLE PASSWORD 

FROZEN MODE is canceled when the power is turned off, or when hardware is 
resented.  If this command is reissued in FROZEN MODE, the command is 
completed and FROZEN MODE remains unchanged. 

Issuing this command during LOCKED MODE returns the Aborted Command 
error. 

The following medium access commands return the Aborted Command error 
when the device is in LOCKED MODE: 

• 

EREAD SECTORS (EXT) 

• 

EREAD LONG 

• 

WRITE SECTORS (EXT) 

• 

WRITE LONG 

• 

WRITE VERIFY 

• 

READ VERIFY SECTORS (EXT) 

• 

READ MULTIPLE (EXT) 

• 

WRITE MULTIPLE (EXT) 

• 

READ DMA (EXT) 

• 

WRITE DMA (EXT) 

• 

DEVICE CONFIGURAION RESTORE 

• 

DEVICE CONFIGURAION SET 

• 

SECURITY SET PASSWORD 

• 

SECURITY FREEZE LOCK 

• 

SECURITY DISABLE PASSWORD 

• 

FLUSH CACHE (EXT) 

• 

SET MAX ADDRESS (EXT) 

 

 

Summary of Contents for MHU2100AT























































































































































































































































































Reviews:

No comments