Fujitsu MHU2100AT Product Manual Download Page 207

Page: 207 / 278

5.4 Command Protocol

C141-E202-01EN 5-131

5.4.3 Commands without data transfer

Execution of the following commands does not involve data transfer between the
host and the device.

•

RECABLIBRATE

•

READY VERIFY SECTOR(S) (EXT)

•

SEEK

•

EXECUTE DEVICE DIAGNOSTIC

•

INITIALIZE DEVICE PARAMETERS

•

STANDBY IMMEDIATE

•

IDLE IMMEDIATE

•

STANDBY

•

IDLE

•

CHECK POWER MODE

•

SLEEP

•

SMART ENABLE/DISABLE AUTOSAVE

•

SMART EXECUTE OFFLINE IMMEDIATE

•

SMART ENABLE OPERATION

•

SMART DISABLE OPERATION

•

SMART RETURN STATUS

•

DEVICE CONFIGURATION RESTORE

•

DEVICE CONFIGURAION FREEZE LOCK

•

SET MULTIPLE MODE

•

FLUSH CACHE (EXT)

•

SET FEATURES

•

SECURITY ERASE PREPARE

•

SECURITY FREEZE LOCK

•

READ NATIVE MAX ADDRESS (EXT)

•

SET MAX ADDRESS (EXT)

Figure 5.6 shows the protocol for the command execution without data transfer.

Summary of Contents for MHU2100AT























































































































































































































































































Search results

Summary of Contents for MHU2100AT

Reviews:

Related manuals for MHU2100AT

Brands by name

Popular brands

Fujitsu MHU2100AT, Product Manual

Search results

Summary of Contents for MHU2100AT

Reviews:

Related manuals for MHU2100AT

Brands by name

Popular brands