Fujitsu MHU2100AT Product Manual Download Page 26 | Manualshive

Page: 26 / 278

background image

Device Overview

1-2 C141-E202-01EN

1.1 Features

1.1.1 Functions and performance

The following features of the disk drive is described.

(1) Compact

The disk drive has 2 disks of 65 mm (2.5 inches) diameter, and its height is 9.5
mm (0.374 inch).

(2) Large capacity

The disk drive can record up to 50 GB (formatted) on one disk using the RLL
recording method and 30 recording zone technology. The disk drive has a
formatted capacity of 100 GB (MHU2100AT).

(3) High-speed Transfer rate

The disk drive (the MHU Series) has an internal data rate up to 41.3 MB/s. The
disk drive supports an external data rate up to 100 MB/s (U-DMA mode 5).

(4) Average positioning time

Use of a rotary voice coil motor in the head positioning mechanism greatly
increases the positioning speed. The average positioning time is 12 ms (at read).

1.1.2 Adaptability

(1) Power save mode

The power save mode feature for Idle operation, Standby and Sleep modes makes
the disk drive ideal for applications where power consumption is a factor.

(2) Wide temperature range

The disk drive can be used over a wide temperature range
(5 °C to 55 °C).

(3) Low noise and vibration

In Ready status (while the device is waiting for any commands), the Sound Power
level of the disk drives in idle mode is 2.4B(A). The Sound Pressure level is
25dB(A), as measured 0.3 m from the drive in Idle mode.

(4) High resistance against shock

The Load/Unload mechanism is highly resistant against non-operation shock up
to 8820 m/s

2

(900G).

«
...
24
25
26
27
28
...
»

Summary of Contents for MHU2100AT























































































































































































































































































Reviews:

No comments

Related manuals for MHU2100AT

05DTMBAX0307DD-V1

Brand: Mercia Garden Products Pages: 9

Brand: Hama Pages: 8

Brand: IAC INDUSTRIES Pages: 8

Brand: dallmeier Pages: 32

GridLine 930505

Brand: GARANT Pages: 116

Brand: Transcend Pages: 25

Brand: Frontier Pages: 9

Brand: Seagate Pages: 42

Brand: LaCie Pages: 2

Brand: Excel Pages: 2

Brand: IBM Pages: 11

PowerProtect X400

Brand: Dell EMC Pages: 42

Deskstar T7K500

Brand: Hitachi Pages: 2

DKC-F710I-1R6FM

Brand: Hitachi Pages: 3

Brand: Hitachi Pages: 6

Brand: Hitachi Pages: 1

Brand: Hitachi Pages: 1

External USB Storage

Brand: Hitachi Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands