Fujitsu MHU2100AT Product Manual Download Page 216 | Manualshive

Page: 216 / 278

background image

Interface

5-140 C141-E202-01EN

5.5.4 Ultra DMA data out commands

5.5.4.1 Initiating an Ultra DMA data out burst

The following steps shall occur in the order they are listed unless otherwise
specifically allowed (see 5.6.3.7 and 5.6.3.2 for specific timing requirements):

1) The host shall keep DMACK- in the negated state before an Ultra DMA burst

is initiated.

2) The device shall assert DMARQ to initiate an Ultra DMA burst.

3) Steps (3), (4), and (5) may occur in any order or at the same time. The host

shall assert STOP.

4) The host shall assert HSTROBE.

5) The host shall negate CS0-, CS1-, DA2, DA1, and DA0. The host shall keep

CS0-, CS1-, DA2, DA1, and DA0 negated until after negating DMACK- at
the end of the burst.

6) Steps (3), (4), and (5) shall have occurred at least t

ACK

before the host asserts

DMACK-. The host shall keep DMACK- asserted until the end of an Ultra
DMA burst.

7) The device may negate DDMARDY- t

ZIORDY

after the host has asserted

DMACK-. Once the device has negated DDMARDY-, the device shall not
release DDMARDY- until after the host has negated DMACK- at the end of
an Ultra DMA burst.

8) The host shall negate STOP within t

ENV

after asserting DMACK-. The host

shall not assert STOP until after the first negation of HSTROBE.

9) The device shall assert DDMARDY- within t

LI

after the host has negated

STOP. After asserting DMARQ and DDMARDY- the device shall not
negate either signal until after the first negation of HSTROBE by the host.

10) The host shall drive the first word of the data transfer onto DD (15:0). This

step may occur any time during Ultra DMA burst initiation.

11) To transfer the first word of data: the host shall negate HSTROBE no sooner

than t

LI

after the device has asserted DDMARDY-. The host shall negate

HSTROBE no sooner than t

DVS

after the driving the first word of data onto DD

(15:0).

«
...
214
215
216
217
218
...
»

Summary of Contents for MHU2100AT























































































































































































































































































Reviews:

No comments

Related manuals for MHU2100AT

Brand: Facom Pages: 4

Brand: U.S. General Pages: 6

Brand: U-Line Pages: 2

SYSTEM STORAGE EXP3000 - INTEROPERABILITY MATRIX...

Brand: IBM Pages: 16

301300U - Ethernet Disk NAS Server

Brand: LaCie Pages: 62

Brand: Eastech Flow Controls Pages: 2

TOWERSTOR TS5CT

Brand: Sans Digital Pages: 33

StorageTek T10000D

Brand: Oracle Pages: 51

Brand: DIVERSIFIED WOODCRAFTS Pages: 6

Backup Exec 3600 R3

Brand: Symantec Pages: 22

Brand: Sanyo Pages: 8

Brand: Sanyo Pages: 26

ELITEPOB-450-218

Brand: Elite Pages: 2

ELITEPOB-300SLIM-0215

Brand: Elite Pages: 2

8x12 SpaceMaker Garden Shed

Brand: OLT Pages: 36

Brand: QNAP Pages: 49

Passio CAXH3701T0

Brand: Cavalry Pages: 1

Brand: Cavalry Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands