Fujitsu MHS2020AT Product Manual Download Page 194 | Manualshive

Page: 194 / 254

background image

Interface

5-118

C141-E171-03EN

NOTE - The host shall not immediately assert STOP to initiate Ultra

DMA burst termination when the device stops generating
STROBE edges. If the device does not negate DMARQ, in
order to initiate ULTRA DMA burst termination, the host shall
negate HDMARDY- and wait t

RP

before asserting STOP.

3)

The device shall resume an Ultra DMA burst by generating a DSTROBE
edge.

b)

Host pausing an Ultra DMA data in burst

1)

The host shall not pause an Ultra DMA burst until at least one data word
of an Ultra DMA burst has been transferred.

2)

The host shall pause an Ultra DMA burst by negating HDMARDY-.

3)

The device shall stop generating DSTROBE edges within t

RFS

of the host

negating HDMARDY-.

4)

If the host negates HDMARDY- within t

SR

after the device has generated

a DSTROBE edge, then the host shall be prepared to receive zero or one
additional data words. If the host negates HDMARDY- greater than t

SR

after the device has generated a DSTROBE edge, then the host shall be
prepared to receive zero, one or two additional data words. The
additional data words are a result of cable round trip delay and t

RFS

timing

for the device.

5)

The host shall resume an Ultra DMA burst by asserting HDMARDY-.

5.5.3.4 Terminating an Ultra DMA data in burst

a)

Device terminating an Ultra DMA data in burst

The following steps shall occur in the order they are listed unless otherwise
specifically allowed (see 5.6.3.5 and 5.6.3.2 for specific timing
requirements):

1)

The device shall initiate termination of an Ultra DMA burst by not
generating DSTROBE edges.

2)

The device shall negate DMARQ no sooner than t

SS

after generating the

last DSTROBE edge. The device shall not assert DMARQ again until
after the Ultra DMA burst is terminated.

3)

The device shall release DD (15:0) no later than t

AZ

after negating

DMARQ.

4)

The host shall assert STOP within t

LI

after the device has negated

DMARQ. The host shall not negate STOP again until after the Ultra
DMA burst is terminated.

5)

The host shall negate HDMARDY- within t

LI

after the device has negated

DMARQ. The host shall continue to negate HDMARDY- until the Ultra
DMA burst is terminated. Steps (4) and (5) may occur at the same time.

«
...
192
193
194
195
196
...
»

Summary of Contents for MHS2020AT































































































































































































































































Reviews:

No comments

Related manuals for MHS2020AT

G-DRIVE mobile USB

Brand: G-Technology Pages: 13

Brand: DuraMax Pages: 81

Rapid Mount 9909-3-02

Brand: Weather Guard Pages: 9

RACK PRO MINI-SAS

Brand: OWC Pages: 12

Brand: Ricoh Pages: 15

Brand: Husky Pages: 14

TS-h2483XU-RP Series

Brand: QNAP Pages: 12

Barracuda 5400.1 ST340015A

Brand: Seagate Pages: 2

HUS151414VL3600

Brand: Hitachi Pages: 5

HUS157336EL3600

Brand: Hitachi Pages: 4

Hyper Scale-Out

Brand: Hitachi Pages: 42

Brand: Hitachi Pages: 4

HTS548020M9AT00

Brand: Hitachi Pages: 2

Brand: Hitachi Pages: 2

HUSSL4040BSS600

Brand: Hitachi Pages: 2

LifeStudio Desk

Brand: Hitachi Pages: 2

HUS156060VLS600

Brand: Hitachi Pages: 2

HUS157336EL3600

Brand: Hitachi Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands