Fujitsu MHS2020AT Product Manual Download Page 192 | Manualshive

Page: 192 / 254

background image

Interface

5-116

C141-E171-03EN

device compares its CRC data to the data sent from the host. If the two values do
not match the device reports an error in the error register at the end of the
command. If an error occurs during one or more Ultra DMA bursts for any one
command, at the end of the command, the device shall report the first error that
occurred.

5.5.2 Phases of operation

An Ultra DMA data transfer is accomplished through a series of Ultra DMA data
in or data out bursts. Each Ultra DMA burst has three mandatory phases of
operation: the initiation phase, the data transfer phase, and the Ultra DMA burst
termination phase. In addition, an Ultra DMA burst may be paused during the
data transfer phase (see 5.5.3 and 5.5.4 for the detailed protocol descriptions for
each of these phases, 5.6 defines the specific timing requirements). In the
following rules DMARDY- is used in cases that could apply to either
DDMARDY- or HDMARDY-, and STROBE is used in cases that could apply to
either DSTROBE or HSTROBE. The following are general Ultra DMA rules.

a)

An Ultra DMA burst is defined as the period from an assertion of DMACK-
by the host to the subsequent negation of DMACK-.

b)

A recipient shall be prepared to receive at least two data words whenever it
enters or resumes an Ultra DMA burst.

5.5.3 Ultra DMA data in commands

5.5.3.1 Initiating an Ultra DMA data in burst

The following steps shall occur in the order they are listed unless otherwise
specifically allowed (see 5.6.3.1 and 5.6.3.2 for specific timing requirements):

1)

The host shall keep DMACK- in the negated state before an Ultra DMA burst
is initiated.

2)

The device shall assert DMARQ to initiate an Ultra DMA burst. After
assertion of DMARQ the device shall not negate DMARQ until after the first
negation of DSTROBE.

3)

Steps (3), (4) and (5) may occur in any order or at the same time. The host
shall assert STOP.

4)

The host shall negate HDMARDY-.

5)

The host shall negate CS0-, CS1-, DA2, DA1, and DA0. The host shall keep
CS0-, CS1-, DA2, DA1, and DA0 negated until after negating DMACK- at
the end of the burst.

6)

Steps (3), (4) and (5) shall have occurred at least t

ACK

before the host asserts

DMACK-. The host shall keep DMACK- asserted until the end of an Ultra
DMA burst.

7)

The host shall release DD (15:0) within t

AZ

after asserting DMACK-.

«
...
190
191
192
193
194
...
»

Summary of Contents for MHS2020AT































































































































































































































































Reviews:

No comments

Related manuals for MHS2020AT

Brand: Campbell Pages: 46

Brand: TRINITY Pro Pages: 12

Brand: OYEN DIGITAL Pages: 2

Brand: ICON Pages: 22

auto-vacuum VAC-20

Brand: German pool Pages: 16

Brand: Backyard Pages: 60

Brand: LaCie Pages: 2

Brand: HANYOUNG NUX Pages: 2

Brand: Fujitsu Pages: 40

ETERNUS2000 100

Brand: Fujitsu Pages: 21

Brand: Fujitsu Pages: 90

Brand: Fujitsu Pages: 12

Brand: Fujitsu Pages: 14

ETERNUS LT40 S2

Brand: Fujitsu Pages: 110

ETERNUS Multipath Driver V2

Brand: Fujitsu Pages: 140

ETERNUS SF Express V16.6

Brand: Fujitsu Pages: 378

GRANPOWER 5000 GP5-HDH451

Brand: Fujitsu Pages: 10

Brand: Fujitsu Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands