manualshive.com logo in svg

Fujitsu MHS2020AT, Product Manual, Page: 209 / 254

Share
Download
Fujitsu MHS2020AT Product Manual Download Page 209

5.5  Ultra DMA Feature Set

C141-E171-03EN

5-133

5.6.3.3 Sustained Ultra DMA data in burst

5.6.3.2 contains the values for the timings for each of the Ultra DMA Modes.

Note:

DD (15:0) and DSTROBE signals are shown at both the host and the device
to emphasize that cable setting time as well as cable propagation delay shall
not allow the data signals to be considered stable at the host until some time
after they are driven by the device.

Figure 5.12  Sustained Ultra DMA data in burst

DSTROBE

at device

DD(15:0)

at device

DSTROBE

at host

DD(15:0)

at host

t

2CYC

t

CYC

t

DVS

t

DVSIC

t

DVH

t

DVHIC

t

DS

t

DSIC

t

DH

t

DHIC

t

2CYC

t

CYC

t

DVS

t

DVSIC

t

DVH

t

DVHIC

t

DH

t

DHIC

t

DH

t

DHIC

t

DVH

t

DVHIC

t

DS

t

DSIC

Summary of Contents for MHS2020AT































































































































































































































































Reviews:

No comments