Fujitsu MHS2020AT Product Manual Download Page 5 | Manualshive

Page: 5 / 254

background image

C141-E171-03EN

i

Preface

This manual describes the MHS Series, 2.5-inch hard disk drives. These drives
have a built-in controller that is compatible with the ATA interface.

This manual describes the specifications and functions of the drives and explains
in detail how to incorporate the drives into user systems. This manual assumes
that the reader has a basic knowledge of hard disk drives and their
implementations in computer systems.

This manual consists of seven chapters and sections explaining the special
terminology and abbreviations used in this manual:

Overview of Manual

CHAPTER 1

Device Overview

This chapter gives an overview of the MHS Series and describes their features.

CHAPTER 2

Device Configuration

This chapter describes the internal configurations of the MHS Series and the
configuration of the systems in which they operate.

CHAPTER 3

Installation Conditions

This chapter describes the external dimensions, installation conditions, and switch
settings of the MHS Series.

CHAPTER 4

Theory of Device Operation

This chapter describes the operation theory of the MHS Series.

CHAPTER 5

Interface

This chapter describes the interface specifications of the MHS Series.

CHAPTER 6

Operations

This chapter describes the operations of the MHS Series.

Glossary

The glossary describes the technical terms that need to be understood to read this
manual.

Acronyms and Abbreviations

This section gives the meanings of the definitions used in this manual.

«
...
3
4
5
6
7
...
»

Summary of Contents for MHS2020AT































































































































































































































































Reviews:

No comments

Related manuals for MHS2020AT

Brand: Quantum Pages: 54

Brand: Seagate Pages: 28

ValueLoader LTO-2

Brand: Quantum Pages: 94

Brand: Impediment Pages: 256

Brand: Brookstone Pages: 8

Brand: Kval Pages: 72

Insulated Cabin

Brand: DuraMax Pages: 38

MediaLounge DSM-602H

Brand: D-Link Pages: 12

SharePort DNS-323

Brand: D-Link Pages: 17

Brand: D-Link Pages: 46

MediaLounge DSM-622H

Brand: D-Link Pages: 16

MediaLounge DSM-622H

Brand: D-Link Pages: 46

MediaLounge DSM-602H

Brand: D-Link Pages: 39

ShareCenter 2Go - DNS-213

Brand: D-Link Pages: 87

Brand: Memorex Pages: 4

Brand: Medion Pages: 112

Brand: Acomdata Pages: 1

Brand: Planet Pages: 125

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands