Fujitsu MHS2020AT Product Manual Download Page 144 | Manualshive

Page: 144 / 254

background image

Interface

5-68

C141-E171-03EN

Table 5.7 Features Register values (subcommands) and functions (1 of 3)

Features Resister

Function

X’D0’

SMART Read Attribute Values:

A device that received this subcommand asserts the BSY bit and saves all
the updated attribute values. The device then clears the BSY bit and
transfers 512-byte attribute value information to the host.

* For information about the format of the attribute value information, see

Table 5.8.

X’D1’

SMART Read Attribute Thresholds:

This subcommand is used to transfer 512-byte insurance failure threshold
value data to the host.

* For information about the format of the insurance failure threshold value

data, see Table 5.9.

X’D2’

SMART Enable/Disable Attribute AutoSave:

Enables (by setting the SC register to a value other than 00h) or disables (by
setting the SC register to 00h) a function that automatically saves device
attribute values (“automatic attribute save function”). This setting is held
regardless of whether the device is turned on or off. If the automatic
attribute save function is enabled and more than 15 minutes has elapsed
since the last time that attributes were saved, then the attributes are saved.
However, if the automatic attribute save function is disabled, the attributes
are not saved. Upon receiving this subcommand, a device asserts BSY,
enables or disables the automatic attribute save function, and clears BSY.

X’D3’

SMART Save Attribute Values:

When the device receives this subcommand, it asserts the BSY bit, saves
device attribute value data, then clears the BSY bit.

X’D4’

SMART Executive Off-line Immediate:

A device which receives this command asserts the BSY bit, then starts
collecting the off-line data specified in the SN register, or stops.

In the off-line mode, after BSY is cleared, off-line data are collected. In the
captive mode, it collects off-line data with the BSY assertion as is, then
clears the BSY when collection of data is completed.

SN

Off-line data collection mode

00h: Off-line diagnosis (off-line mode)

01h: Simple self test (off-line mode)

02h: Comprehensive self test (off-line mode)

7Fh: Self test stop

81h: Simple self test (captive mode)

82h: Comprehensive self test (captive mode)

«
...
142
143
144
145
146
...
»

Summary of Contents for MHS2020AT































































































































































































































































Reviews:

No comments

Related manuals for MHS2020AT

HD080HJ - 80 GB Hard Drive

Brand: Samsung Pages: 2

G2 PORTABLE HX-MU025DC

Brand: Samsung Pages: 36

Brand: Angelbird Pages: 20

XCubeDAS XD5324D

Brand: Qsan Pages: 49

Brand: Nexsan Pages: 76

Brand: Zhejiang Longyard Trade Industrial Pages: 18

Brand: Swiss Aqua Technologies Pages: 5

Brand: Dancover Pages: 36

GEAR 175-9872-4

Brand: Yukon Pages: 7

DLT-V4 EZ-Kit Series

Brand: Freecom Pages: 2

Brand: Husky Pages: 10

Brand: DFI Pages: 28

Brand: morse Pages: 7

Brand: Cisco Pages: 23

Brand: Cisco Pages: 75

Brand: Cisco Pages: 132

Brand: Cisco Pages: 58

UCS 6400 Series

Brand: Cisco Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands