manualshive.com logo in svg

Fujitsu MHS2020AT, Product Manual

The Fujitsu MHS2020AT product manual is available for free download on our website. This comprehensive manual provides detailed instructions and essential information about the product, ensuring smooth usage and troubleshooting. Visit our website to access this valuable resource and maximize your experience with the Fujitsu MHS2020AT.

Share
Download
background image

5.3  Host Commands

C141-E171-03EN

5-17

Table 5.3 Command code and parameters (3 of 3)

Command code (Bit)

Parameters used

Command name

7

6

5

4

3

2

1

0

FR SC SN CY DH

DEVICE CONFIGURATION
IDENTIFY

1

0

1

1

0

0

0

1

Y

N

N

N

D

DEVICE CONFIGURATION SET

1

0

1

1

0

0

0

1

Y

N

N

N

D

READ NATIVE MAX ADDRESS
EXT

1

1

1

1

1

0

0

0

N

N

N

N

D

SET MAX ADDRESS EXT

1

1

1

1

1

0

0

1

N

Y

Y

Y

Y

FLUSH CACHE EXT

1

1

1

0

0

1

1

1

N

N

N

N

D

WRITE DMA EXT

0

0

1

1

0

1

0

1

N

Y

Y

Y

D

READ DMA EXT

0

0

1

0

0

1

0

1

N

Y

Y

Y

D

WRITE MULTIPLE EXT

0

0

1

1

1

0

0

1

N

Y

Y

Y

D

READ MULTIPLE EXT

0

0

1

0

1

0

0

1

N

Y

Y

Y

D

WRITE SECTOR (S) EXT

0

0

1

1

0

1

0

0

N

Y

Y

Y

D

READ SECTOR (S) EXT

0

0

1

0

0

1

0

0

N

Y

Y

Y

D

Notes:

FR:

Features Register

CY:

Cylinder Registers

SC:

Sector Count Register

DH: Drive/Head Register

SN:

Sector Number Register

R:

Retry at error

1 =  Without retry

0 =  With retry

Y:

Necessary to set parameters

Y*:

Necessary to set parameters under the LBA mode.

N:

Not necessary to set parameters (The parameter is ignored if it is set.)

N*:

May set parameters

D:

The device parameter is valid, and the head parameter is ignored.

Summary of Contents for MHS2020AT































































































































































































































































Reviews:

No comments

Related manuals for MHS2020AT

Quantum Q2000 User Manual preview
Q2000
Brand: Quantum Pages: 54
QNAP TS-1273U User Manual preview
TS-1273U
Brand: QNAP Pages: 62
QNAP HS-210 Hardware User Manual preview
HS-210
Brand: QNAP Pages: 130
IBM TS3400 Maintenance Information preview
TS3400
Brand: IBM Pages: 295
Buffalo BS-GS2008P Quick Setup Manual preview
BS-GS2008P
Brand: Buffalo Pages: 2
IBM 9835-415 Deployment Manual preview
9835-415
Brand: IBM Pages: 126
AIC FB128-LX User Manual preview
FB128-LX
Brand: AIC Pages: 79
EMC CLARiiON CX4-120 Setup Manual preview
CLARiiON CX4-120
Brand: EMC Pages: 62
HGST Ultrastar 7K2 Technical Reference Manual preview
Ultrastar 7K2
Brand: HGST Pages: 51
LevelOne MUS-1001 User Manual preview
MUS-1001
Brand: LevelOne Pages: 85
IBM 10/20 GB TR-5 User Manual preview
10/20 GB TR-5
Brand: IBM Pages: 36
Fujitsu MAY2036RC Product/ Product/Maintenance Manual preview
MAY2036RC Product/
Brand: Fujitsu Pages: 94
Fujitsu MAX3036NC Maintenance Manual preview
MAX3036NC
Brand: Fujitsu Pages: 130
Fujitsu MBA3073FD Product Manual preview
MBA3073FD
Brand: Fujitsu Pages: 106
Fujitsu MBC2036RC SERIES Installation Manual preview
MBC2036RC SERIES
Brand: Fujitsu Pages: 1
Fujitsu MBB2073RC SERIES Product Manual preview
MBB2073RC SERIES
Brand: Fujitsu Pages: 98
Fujitsu MAX3036RC SERIES Product/Maintenance Manual preview
MAX3036RC SERIES
Brand: Fujitsu Pages: 94
Fujitsu MAX3036FC Product/Maintenance Manual preview
MAX3036FC
Brand: Fujitsu Pages: 112

Brands by name

Popular brands

Load more brands