3
Message Displayed
Probable Cause/Event
Corrective/User Action
Drive Overload
Cooling, Wait…
-
The drive motors have been working
under a severe load for too long.
-
There is no need to do anything – Robomow
will renew automatically the operation after the
drive motors will cool down to temperature
that allows operation.
Drive problem
-
Internal failure
-
Contact service provider
Enter Code
-
The theft guard system is activated
-
Enter the correct 4-digit code. ‘Theft Guard’
can be deactivated under ‘User Preferences’.
Contact your service provider for assistance in
a lost code situation.
Front/Rear bumper disc.
-
Internal bumper failure
-
Contact service provider
Front/Rear bumper pressed
-
Front or Rear Bumper is constantly
being pressed
-
Move mower away from object pressing
against bumper.
CAUTION – Remove power pack before lifting
the mower
-
The Robomow has driven onto an obstacle,
raising the front end. Remove or exclude this
object from the mowing area.
-
The Robomow is being used on a slope too
steep for safe mowing. Exclude this from the
mowing area.
-
High grass is preventing the front wheel from
fully riding on the ground. Raise the cutting
height.
Front Wheel Problem
-
The Front Wheel has left the ground for
more than 8 – 10 seconds.
-
The ground contains large holes or indentions
where the front wheel can drop into when
passing across. Fill these areas with dirt and
level off.
High temp.
Disc. charger
-
Robomow is charged through the plug
and ambience temperature is out of
range (above 158ºF / 70ºC)
-
Robomow charging is not allowed when the
ambience temperature is raised above 158ºF /
70ºC; Disconnect the charger plug and wait
until the temperature will go down or take the
Robomow to be charged in a cooler place.
High temp.
Waiting…
-
Robomow is charged through the
Docking Station and the ambience
temperature is out of range (above
158ºF / 70ºC);
-
Do not do anything, the charging is stopped
and Robomow is waiting for temperature to
change back to the allowed range; if
temperature stays out of the range for more
than 12 hours, the message is changed to
‘High temp. Press GO’.
Keep charging if not used
-
Message is displayed every time the
charger plug is disconnected from the
mower.
-
Displayed when the mower isn’t in
operation and not connected to the
charger/Docking for a long time.
-
Press any key to change the display back.
-
Send the mower back to the Docking Station
for charging / connect the charging plug or
continue in operation
Keys locked
-
Child lock feature has been activated
-
Press the Up
⇑
arrow key and then press the
‘C’ button. Child lock can be deactivated
under User preferences.
2
Summary of Contents for robomower RL1000
