Friendly Robotics robomower RL1000, Service Manual

Page: 58 / 213

3
3
Message Displayed Probable Cause/Event Corrective/User Action
Low battery
- Mower is searching for the Docking
Station but the battery voltage is too
low to continue the searching process
-
Drive the mower manually for charging in the
Docking Station
Low temp.
Disc. charger
- Robomow is charged through the plug
and ambience temperature is out of
range (below 32 ºF / 0 ºC); disconnect
the charger plug from the Robomow.
- Robomow charging is not allowed when the
ambience temperature is going down below
32ºF / 0ºC; Disconnect the charger plug and
wait until the temperature will go down or take
the Robomow to be charged in a warmer
place.
Low temp.
Waiting…
- Robomow is charged through the
Docking Station and the ambience
temperature is out of range (below
32ºF / 0ºC);
-
Do not do anything, the charging is stopped
and Robomow is waiting for temperature to
change back to the allowed range; if
temperature stays out of the range for more
than 12 hours, the message is changed to
‘Low temp. Press GO’.
Left/Mid/Right mow problem
Mowing motor is faulty or disconnected Contact service provider
Move from Wire
-
The Robomow is positioned too close
or on top of the perimeter wire
- Move the Robomow approximately 6 – 10 feet
(1.5 – 3m) away from the perimeter wire and
start again.
Mowing Overload
Cooling, Wait
-
The mowing motors have been working
under a severe load for too long of a
time.
-
There is no need to do anything – Robomow
will renew automatically the operation after the
mowing motors will cool down to temperature
that allows operation.
No Wire Signal
-
Perimeter Switch is not turned on or
not connected to the zone intended to
mow
- Make sure the Perimeter Switch is connected
to the correct zone and is turned on
Rain detected
Go to ignore
(Enhanced Manual Controller
only)
- Robomow detects rain upon GO
pressing
- Do not operate Robomow in rainy weather
and wet grass; If you choose to override,
press the GO button; The overriding is valid
for the current operation only
Ready
Keep Charging
- The battery is fully charged
- Keep the charger (power supply) connected
and operating
Recharge Battery
- The maximum operating time has been
reached
-
Connect the charger to the mower
Replace blades
every 200 hours
- An automatic reminder to replace the
blades is displayed every 200 hours
-
Replace the blades and restart the counter of
the blades replacement reminder by choosing
the ‘Blades replaced – Clear reminder’
option under the ‘User Preferences’ menu
Replace lamp
-
The Operating Lamp is burnt out
- Confirm the message and replace the
Operating Bulb as soon as possible
Retry elsewhere
-
Calibration failure from interference in
the immediate area
-
Move the Robomow 10-12 feet (3-4m) from
this spot and attempt calibration again.
Set Country
- Displayed only on first use. - Follow prompts on LCD screen to set country
Set Time
-
Displayed every time the power pack is
taken out of the mower (reset
operation)
-
Set real time clock (day and hour)
Skipped: Low bat
- Robomow has skipped the last depart
due to low battery voltage
-
Confirm there is enough time between the two
adjacent departures so the battery can be
charged prior the scheduled operation (min 16
hours between operations)
Skipped: Rain
(Only Enhanced Manual
Controller)
- Robomow has skipped the last depart
due to rain detection
-
It is not recommended to cut wet or damp
grass, but if you choose to override the rain
sensor, change the setting of the ‘Rain sensor’
to ‘off’ under the ‘User preferences’ menu.