manualshive.com logo in svg

Fluke ScopeMeter 190 Series, Programming Reference Manual

Share
Download
Fluke ScopeMeter 190 Series Programming Reference Manual Download Page 94

                             Page 3.65
    =============================================================
                   RECALL SETUP                  RS
    -------------------------------------------------------------

    Purpose:

       Recalls an internally stored setup. This setup must have
       been stored in the ScopeMeter manually or with the SS
       (Save Setup) command.
       The effect of the RS command is that the instrument setup
       is recalled and the instrument forced to running state.

    Command Syntax:

       RS <setup_reg><cr>

       where,

       <setup_reg> = 1 to 15     : Screen/Setup memories
                     1001        : Long Record/Replay memory Input A
                     1002        : Long Record/Replay memory Input B

    Response Syntax:

       <acknowledge><cr>

       Note: The new setup is active when you have received the
             <acknowledge> response from the ScopeMeter.

    Example:

    The following example program saves the present setup in
    setup memory 8. You are requested to change the present
    settings. Then the original settings are recalled from
    setup memory 8 and made the actual setting.

Summary of Contents for ScopeMeter 190 Series

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands