manualshive.com logo in svg

Fluke ScopeMeter 190 Series, Programming Reference Manual

Share
Download
Fluke ScopeMeter 190 Series Programming Reference Manual Download Page 29

    ’                        Page 3.18

    ’*****************  Begin example program  *****************

    CLS                     ’Clears the PC screen.
    OPEN "COM1:1200,N,8,1,CS,DS,RB2048" FOR RANDOM AS #1
    PRINT #1, "GR"          ’Sends GO TO REMOTE command.
    GOSUB Acknowledge       ’Input acknowledge from ScopeMeter.
    PRINT "All ScopeMeter keys (except the Power ON/OFF key)
    PRINT "are now disabled by the GR (GO TO REMOTE) command."
    PRINT "Check this."
    PRINT
    PRINT "Press any key on the PC keyboard to continue."
    SLEEP
    PRINT
    PRINT #1, "GL"          ’Sends GO TO LOCAL command.
    GOSUB Acknowledge       ’Input acknowledge from ScopeMeter.
    PRINT "The ScopeMeter keys are now enabled again by the "
    PRINT "GL (GO TO LOCAL) command."
    PRINT "Check this."
    CLOSE #1
    END

    ’

Summary of Contents for ScopeMeter 190 Series

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands