manualshive.com logo in svg

Fluke ScopeMeter 190 Series, Programming Reference Manual

Share
Download
Fluke ScopeMeter 190 Series Programming Reference Manual Download Page 89

                             Page 3.61
    =============================================================
                   RESET INSTRUMENT              RI
    -------------------------------------------------------------

    Purpose:

       Resets the entire instrument, including the CPL interface.
       The baud rate remains unchanged.

    Command Syntax:

       RI<cr>

    Response Syntax:

       <acknowledge><cr>

       Note:    Wait for at least 2 seconds after the
                <acknowledge> reply has been received, to let
                the ScopeMeter settle itself before you send the
                next command.

    Example:

    The following example resets the ScopeMeter and waits for 2
    seconds to let the ScopeMeter execute the reset and become
    ready for next commands.
    The ScopeMeter is queried for the identification data; this
    data is input and displayed on the PC screen.

Summary of Contents for ScopeMeter 190 Series

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands