manualshive.com logo in svg

Fluke ScopeMeter 190 Series, Programming Reference Manual

Share
Download
Fluke ScopeMeter 190 Series Programming Reference Manual Download Page 36

                             Page 3.25
    =============================================================
                   INSTRUMENT STATUS             IS
    -------------------------------------------------------------

    Purpose:

       Queries the contents of the ScopeMeter’s status register.
       The returned value reflects the present operational status
       of the ScopeMeter. This is a 16-bit word, presented as an
       integer value, where each bit represents the Boolean value
       of a related event.

    Command Syntax:

       IS<cr>

    Response Syntax:

       <acknowledge><cr>[<status><cr>]

       where,

       <status> =    integer value 0 to 65535

       <status>
       Bit  Value    Status Description
       ----------------------------------------------------------
        0      1     Maintenance mode
        1      2     Charging
        2      4     Recording
        3      8     AutoRanging
        4     16     Remote
        5     32     Battery Connected
        6     64     Power (Net) Adapter connected
        7    128     Calibration necessary
        8    256     Instrument Held (HOLD status)
        9    512     Pre Calibration busy
       10   1024     Pre Calibration valid
       11   2048     Replay buffer full
       12   4096     Triggered
       13   8192     Instrument On
       14  16384     Instrument Reset occurred
       15  32768     Next <status> value available

    Example:

Summary of Contents for ScopeMeter 190 Series

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands