manualshive.com logo in svg

Fluke ScopeMeter 190 Series, Programming Reference Manual

Share
Download
Fluke ScopeMeter 190 Series Programming Reference Manual Download Page 39

                             Page 3.28
    =============================================================
                   PROGRAM COMMUNICATION         PC
    -------------------------------------------------------------

    Purpose:

       Programs the baud rate for RS232 communication:

    Command Syntax:

       PC <baudrate>

       where,

       <baudrate>  =   1200|2400|4800|9600|19200
                       38400 (Fluke 19xC)
                       57600 (Fluke 19xC, PM9080/101 required)

       The default baudrate is 1200. This is set at power-on or
       after a Reset Instrument command (command "RI")

       Notes:
             The Fluke 19x/19xC instruments support 1 stopbit,
             8 databits and  software handshake (X-on X-off
             protocol).
             Hardware handshaking is not supported.

Summary of Contents for ScopeMeter 190 Series

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands