manualshive.com logo in svg

Fluke ScopeMeter 190 Series, Programming Reference Manual

Share
Download
Fluke ScopeMeter 190 Series Programming Reference Manual Download Page 62

                       21      TrendPlot 2:
                                 Min/Max/Average trace
                       22      Scope mode:
                                 Min/Max trace INPUT B ENVELOPE
                       23      Scope mode:
                                 Min/Max trace INPUT B REFERENCE
                       30      Scope mode, Mathematics:
                                 Min/Max trace A+B, A-B or AxB

       V | v      Trace values (samples) only
       S | s      Setup (administration) data only. When V or S is
                  omitted, trace values and setup data are returned.

    Response Syntax:

       <acknowledge><cr>[<trace_data><cr>]

       where,

       <trace_data> = <trace_admin> | <trace_samples> |
                      <trace_admin>,<trace_samples>

       If the optional parameter (V or S) is omitted:

       <trace_data> = <trace_admin>,<trace_samples><cr>
       This includes the complete information about the trace
       (waveform). For detailed descriptions about the waveform
       structure, refer to Appendix C.

Summary of Contents for ScopeMeter 190 Series

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands