manualshive.com logo in svg

Fluke ScopeMeter 190 Series, Programming Reference Manual

Share
Download
Fluke ScopeMeter 190 Series Programming Reference Manual Download Page 16

                             Page 3.5
    =============================================================
                   AUTO SETUP                    AS
    -------------------------------------------------------------

    Purpose:

       Invokes an automatic setup for the active mode. The result
       of this command is the same as pressing the AUTO key
       on the ScopeMeter.

       Note:  You can select the items that are affected by the
              AUTO SET procedure via the USER OPTIONS key on
              the ScopeMeter.

    Command Syntax:

       AS<cr>

    Response Syntax:

       <acknowledge><cr>

    Example:

    The following example program sends an AUTO SETUP command to
    the ScopeMeter. Connect a repetitive signal on
    INPUT A to see the effect of AUTO SETUP.

Summary of Contents for ScopeMeter 190 Series

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands