manualshive.com logo in svg

Fluke ScopeMeter 190 Series, Programming Reference Manual

Share
Download
Fluke ScopeMeter 190 Series Programming Reference Manual Download Page 24

                             Page 3.13
    =============================================================
                   DEFAULT SETUP                 DS
    -------------------------------------------------------------

    Purpose:

       Resets the ScopeMeter to the factory settings at
       delivery, except for the RS232 communication settings such
       as baud rate, to keep the communication alive.
       A Master Reset (refer to the Users Manual) performs the
       same, but also resets the RS232 communication settings to
       the default values.

    Command Syntax:

       DS<cr>

    Response Syntax:

       <acknowledge><cr>

       Note:    Wait for at least 2 seconds after the
                <acknowledge> reply has been received, to let
                the ScopeMeter settle itself before you send the
                next command.

    Example:

Summary of Contents for ScopeMeter 190 Series

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands