Fidelity Measurement AFM18 Operation Manual Download Page 67

Page: 67 / 78

www.fi-measurement.com

10. Battery Power & Recharging

Remaining battery power of the built-in rechargeable battery is displayed on

the

BATTERY POWER / LEVEL INDICATOR.

10.1 Symbols and Remaining Power

≥ 6.3V

≥6.0V

≥5.7V

<5.7V

10.2 Battery Operation Time

Depends on the battery condition, a new and fully charged rechargeable

battery can provide

: -

•

around 70 hours of continuous operation with backlight on, or

•

around 200 hours of continuous operation without backlight.

10.3 Recharge Battery

When appears, (when battery is less than 5.7V), it means that the

built-in rechargeable battery is at low voltage status. Recharge battery as soon

as possible.

To protect the built-in rechargeable battery, this instrument will be powered off

automatically when battery is at extremely low level. If this is the case, do not

attempt to power this instrument on. Recharge this instrument immediately.

Fail to do so may cause unrecoverable damages to the built-in rechargeable

battery.

Battery charging status is shown on the dual color

CHARGE STATUS

INDICATOR

: -

•

Red: - Recharging in process,

•

Green: - Charging completed.

When connect to one 350 ohm load cell.

Summary of Contents for AFM18















































































Search results

Summary of Contents for AFM18

Reviews:

Brands by name

Popular brands

Fidelity Measurement AFM18, Operation Manual

Search results

Summary of Contents for AFM18

Reviews:

Brands by name

Popular brands