Fidelity Measurement AFM18 Operation Manual Download Page 10

Page: 10 / 78

www.fi-measurement.com

12. CHECK SYMBOLS

•

Hi = Weight reading is higher than the Hi limit entered,

•

OK = Weight reading is in between than the Lo and Hi limits entered,

•

Lo = Weight reading is lower than the Lo limit entered.

13. W

INDICATOR

(When under dual weighing range mode

) Visible when this instrument is in the

first weighing range (W

14. W

INDICATOR

(When under dual weighing range mode) Visible when this instrument is in the

second weighing range (W

15. SPARE

Blank, no function assigned.

16. M+ INDICATOR

Visible when the total accumulated weight value is being displayed.

17. BATTERY POWER / LEVEL INDICATOR

Visible to show: -

•

This instrument is being powered by the built-in rechargeable battery,

•

Remaining battery level.

18. HOLD INDICATOR

(When under animal mode) Visible when weight reading being displayed is a

frozen value.

19. AUTO INDICATOR

Visible when the instrument is in animal weighing function.

This indicator will not appear when this instrument is in single range mode.

This instrument can support two weighing ranges with different maximum capacities (Max) and

different scale intervals (d), each range extending from zero to its maximum capacity.

This indicator will not appear when this instrument is in single range mode

Summary of Contents for AFM18















































































Search results

Summary of Contents for AFM18

Reviews:

Brands by name

Popular brands

Fidelity Measurement AFM18, Operation Manual

Search results

Summary of Contents for AFM18

Reviews:

Brands by name

Popular brands