Fidelity Measurement AFM18 Operation Manual Download Page 6

Page: 6 / 78

www.fi-measurement.com

1. Installation

Because of metrological legislation, installation / some metrological parameter

settings are limited to be done by authorized personnel only. Do not attempt to

change any of the built-in parameters. Contact your dealer for installation and

technical assistance.

Caution: -

This instrument is legal for trade only when it is sealed (and/or stamped) and

bearing a serial number. Do not attempt to break the seal (or stamp) affixed to

this instrument and/or remove the serial number. Contact your dealer for more

information and after sales service.

For most accurate weighing result, do not use the unit in where or when the

environment condition falls beyond as those listed on

Specifications

Do not attempt to open this instrument or conduct any trouble shootings.

Summary of Contents for AFM18















































































Search results

Summary of Contents for AFM18

Reviews:

Brands by name

Popular brands

Fidelity Measurement AFM18, Operation Manual

Search results

Summary of Contents for AFM18

Reviews:

Brands by name

Popular brands