Fidelity Measurement AFM18 Operation Manual Download Page 16

Page: 16 / 78

www.fi-measurement.com

4.3.3 Connecting RS232 to Printer (DB25)

RS232 COMPORT (DB9) ON

INSTRUMENT

COMPUTER COM DB25

2 = RXD

3 = TXD

2 = RXD

5 = GND

7 = GND

4.3.4 Connecting the Optional External Relay Output Module

If the optional relay output module is purchased, simply plug in the DB-25

connector of the relay output module to the TTL & relay output port by using

the accessory enclosed.

4.3.5 Connecting to TTL Relay Devices by Others

Follow the below

TTL RELAY OUTPUT PORT PIN ASSIGNMENT TABLE

for

connection.

This instrument provides low-active TTL relay signals. Do not connect the TTL

relay output port to any other non-TTL relay devices; they may cause

unrecoverable damages to this instrument.

TTL RELAY OUTPUT PORT PIN ASSIGNMENT TABLE (LOW-ACTIVE)

RELAY OUTPUT PIN #

ASSIGNMENT

BUZZER

DC+5v Output

Ground

4.3.6 Connecting the Optional Wireless Data Communication Module

If the optional WM-SP wireless data communication module is purchased,

simply plug it into the TTL COMPORT.

Summary of Contents for AFM18















































































Search results

Summary of Contents for AFM18

Reviews:

Brands by name

Popular brands

Fidelity Measurement AFM18, Operation Manual

Search results

Summary of Contents for AFM18

Reviews:

Brands by name

Popular brands